Blizzard B74C Скачать руководство пользователя

Страница: 40 / 52

MAINTENANCE

OM 0410SB-A

Note: Shield bearings must be greased every 8 working hours.

AVOIDABLE DAMAGES

POSSIBLE CAUSES

CORRECTIVE ACTIONS

SHIELD



Excessive wear of shield

bearings.



Insufficient

lubrication.



Incorrect chain mounting.



Shield

interfering

with

implement.



Follow lubrication instructions.



Mount chain to allow

maximum angularity.



Avoid contact of the shields

with fixed parts of the machine
or tractor.



Replace shield bearings.



Chain moving or failure.



Shield

interfering

with

implement.



Incorrect chain mounting.



Avoid contact of the shields

with fixed parts of the machine
or tractor.



Mount chain to allow

maximum angularity.



Replace defective parts.



Shield

cone

damaged.



Shield cone in contact with

components on the tractor
and/or implement.



Excessive

angularity.



Eliminate

interference

between Shield cones and any
part on the tractor and/or
implement.



Avoid excessive angle during

cornering or when lifting or
lowering the implement.



Replace damaged Shield

cones.



Shield tubes damaged
(deformed and split at one
side).



Shields in contact with

components on the tractor
and/or implement.



Shield tubes overlap too

short or no overlap at all
with extended driveline.



Eliminate

interference

between Shield cones and
any part on the tractor and/or
implement.



Replace

damaged

tubes.



Adjust Shield tubes length

with longer tubes.

Содержание B74C





















































Результаты поиска

Содержание B74C

Отзывы:

Похожие инструкции для B74C

Бренды по названию

Популярные бренды

Blizzard B74C, Руководство оператора и каталог запасных частей

Результаты поиска

Содержание B74C

Отзывы:

Похожие инструкции для B74C

Бренды по названию

Популярные бренды