Blizzard B74C Скачать руководство пользователя | Manualshive

Страница: 28 / 52

background image

ASSEMBLY

OM 0410SB-A

26

IMPORTANT

:

A proper initial installation will give you years of
satisfactory service on your equipment. Please
read carefully following instructions that have
been specially included to help you and ensure
you are satisfied with your purchase.

WARNING

Unfortunately, snowblowers will be faced
with forgotten or hidden objects under the
snow, such as : chain, tires, stones, pieces
of wood, etc. In spite of all our efforts,
machines are not built to resist all those
conditions.

Danger: Tractors Too Big

It is dangerous to use a tractor that is too big and
powerful. The tractor will always be able to
overload the blower, even if the machine is
already at maximum capacity. Furthermore,
tractors being very high, the driveline angles will
be excessive which means the universal joints
will be very vulnerable and the life of the driveline
will be dramatically reduced.

How to Determine Driveline Angles

IMPORTANT:

To obtain the proper universal

joint angles, it is recommended to adjust the
three point hitch at the furthest point from the
tractor recommended by the manufacturer

The universal joint angle is directly related with
the life of driveline. In order to reduce the angle, it
is necessary to increase the distance between
the snowblower and the tractor.

Angles of Driveline Joints Too Large

Avoid

Reasonable Angles of Driveline Joints

Acceptable

«
...
26
27
28
29
30
...
»

Содержание B74C





















































Отзывы:

Нет отзывов

Похожие инструкции для B74C

Бренд: Zenoah Страницы: 15

Бренд: Nilfisk-Advance Страницы: 295

Бренд: Grizzly Страницы: 144

Бренд: Yard Machines Страницы: 28

CLASSIC LBC15-BS950

Бренд: Scag Power Equipment Страницы: 23

Allied Binary Series

Бренд: Farm King Страницы: 100

Бренд: Ryobi Страницы: 76

Бренд: sunjoe Страницы: 12

Бренд: sunjoe Страницы: 16

Бренд: Dunsch Страницы: 24

Бренд: Scotts Страницы: 21

Бренд: Scotts Страницы: 21

Бренд: Scotts Страницы: 30

Бренд: Dolmar Страницы: 204

Бренд: LOFTNESS Страницы: 35

Бренд: LOFTNESS Страницы: 36

Бренд: LOFTNESS Страницы: 37

Бренд: LOFTNESS Страницы: 38

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды