Blizzard B74C Скачать руководство пользователя | Manualshive

Страница: 20 / 52

background image

ASSEMBLY

OM 0410SB-A

18

1. Hydraulic hose
2. Cardboard
3. Magnifying glass

Installation of Hydraulic Rotation Kit BER0078

(Figures 8 to 12)

1.

Install the chute according to the instructions
contained in the snowblower Operator's
Manual.

2. Figure

10:

Place the motor spacer (item 2) on

the motor top (item 1) by aligning the holes.
Install the motor (item 1) under the frame
base of the snowblower and secure with four
3/8’’NC x 1’’ bolts (item 3), four 3/8"
lockwashers (item 4) and four 3/8" (7/16"
hole) flat washers (item 5). Torque slightly.

3. Figure 10:

Make sure the Woodruf key is on

the motor shaft and insert the motor gear
(item 6) on the shaft. Secure with a 1/4’’NC x
1’’ bolt (item 7), a 1/4" lockwasher (item 8)
and a 1/4" (5/16" hole) flat washer (item 9).

4. Figure 11:

NOT INCLUDED:

Using thread

sealant, install a 1/4"NPT female x 1/2"NPT
male reducer (item 2), a male quick coupler
(item 3) and a dust cap (item 4) on each
straight end of the hoses (item 1).

CAUTION

To avoid serious personal injury.

Escaping

hydraulic/ diesel fluid under pressure can
penetrate the skin causing serious injury.

•

Do not use your hands to
check for leaks. Use a
piece of cardboard or
paper to search for leaks.

•

Stop engine and relieve pressure before
connecting or disconnecting lines.

•

Tighten all connections before starting
engine or pressurizing lines.

•

If any fluid is injected into the skin, obtain
medical attention immediately or gangrene
may result.

Figure 8

Figure 9

«
...
18
19
20
21
22
...
»

Содержание B74C





















































Отзывы:

Нет отзывов

Похожие инструкции для B74C

Бренд: EGO Страницы: 120

Бренд: Gardol Страницы: 188

Бренд: sunjoe Страницы: 15

Minute Mount 2 XV2 Series

Бренд: Fisher Страницы: 16

Бренд: Troy-Bilt Страницы: 48

Бренд: Giant-Vac Страницы: 16

Бренд: Echo Страницы: 36

Бренд: Erskine Attachments Страницы: 36

Бренд: ebm-papst Страницы: 11

Бренд: ebm-papst Страницы: 11

Бренд: Snapper Страницы: 116

Бренд: Troy-Bilt Страницы: 24

Бренд: Power smart Страницы: 71

Бренд: Sabo Страницы: 52

Бренд: Yard-Man Страницы: 32

Бренд: Zenoah Страницы: 36

EVAPORATOR BLOWERS K2EU060

Бренд: York Страницы: 28

Бренд: Gardena Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды