manualshive.com logo in svg

Blaze King Clarity CL29.IPI, Руководство по эксплуатации и установке

Поделиться
Скачать
Blaze King Clarity CL29.IPI Скачать руководство пользователя страница 6

180-CL29-SP v1.00

March 12, 2019

Page 6

Clarity CL29 SP

SPECIFICATIONS

MODEL

CL29.SP

Natural Gas (NG)

Propane (LP)

Manifold Pressure

3.8 in. w.c. (0.95kPa)

11.0 in. w.c. (2.74 kPa)

Min. Supply Pressure for 
Purpose of Input Adjustment 

7 in. w.c. (1.74 kPa)

13.0 in. w.c. (3.23 kPa)

Orifi ce Size

DMS #39

DMS #53

Nominal Input Rating

29,500 BTU/hr, 8.65 kWh

 28,500 BTU/hr, 8.35 kWh

Minimum Input Rating

16,000 BTU/hr, 4.69 kWh

14,000 BTU/hr, 4.10 kWh

Altitude

0 - 4,500 ft. (0 - 1372 m)

0 - 4,500 ft. (0 - 1372 m)

Primary Air Opening

1/16”  (Minimum)

1/16”

Electrical  Rating

120 V.A.C. System

120 V.A.C. System

HIGH ALTITUDE INSTALLATION

 

When installing this appliance beyond 4500 ft. (1372 m) above sea level, the appliance must be properly de-
rated and installed according to local codes, in the absence of local codes, with the current National Fuel Gas 
Code, ANSI Z223.1/ NFPA 54, in the US or Installation Code, CSA-B149.1, in Canada.

GENERAL INFORMATION

INSTALLATION CODES

This appliance must be installed by a qualifi ed gas 
appliance installer.  This appliance is certifi ed for installation 
in a bedroom or a bedsitting room.  This appliance is only 
for use with the type of gas indicated on the rating plate and 
may be installed in an aftermarket, permanently located, 
manufactured (mobile) home where not prohibited by 
local codes.  This appliance is not convertible for use with 
other gases, unless a certifi ed kit is used.  Only for direct 
discharge without duct connection. This appliance must 
be direct vented using listed and approved Simpson Dura-
Vent, Selkirk, Security or American Metal Products vent 
components.

We recommend 
that our gas hearth 
products be installed 
and serviced by 
professionals who are 
certifi ed in the U.S. by 
the National Fireplace 
Institute (NFI) as NFI 
Gas Specialists.

APPLIANCE CERTIFICATION

This appliance is tested and certifi ed to the following US and Canadian gas appliance standards:

•  ANSI Z21.88-2017 / CSA 2.33-2017 Vented Gas Fireplace Heaters,
•  CAN/CGA-2.17-M91 (R2014) Gas-Fired Appliance for Use at High Altitudes
•  CSA P.4.1-15 Testing Method for Measuring Annual Fireplace Effi  ciency

STEADY STATE EFFICIENCY

Natural Gas (NG)

Propane (LP)

Steady State Effi

  ciency - High

Eff y

SS,H

62.71%

66.81%

Annual Fireplace Effi

  ciency

FE

59.39%

61.04%

Содержание Clarity CL29.IPI













































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды