background image

180-CL29-SP v1.00

March 12, 2019

Page 4

Clarity CL29 SP

SAFETY PRECAUTIONS

NOTE:

  Failure to follow these instructions could cause a malfunction of the fi replace, which could result in 

death, serious bodily injury, and/or property damage.

GENERAL

•  Installation and repair should be done by a qualifi ed service person.  The appliance should be inspected 

before the fi rst use and, at least, annually by a qualifi ed service person.  More frequent cleaning may 
be required due to excessive lint from carpeting, bedding material, etc.  It is imperative the control 
compartments, burners and circulating air passageways of the appliance be kept clean.

•  If the CLARITY CL29 is pulled out of its installation, and the vent-air intake pipes is disconnected for 

any reason, ensure that the vent-air intake pipes are reconnected and re-sealed in accordance to the 
instructions noted in INSTALLATION - VENT CONNECTOR REMOVAL AND INSTALLATION.

•  Due to high temperatures, the appliance should be located out of high traffi  c areas and away from furniture 

and draperies.

Children and adults should be alerted to the hazards of high surface

temperatures and should stay away to avoid burn or clothing ignition.

•  Young children should be carefully supervised when in the same room as the appliance.  Toddlers, young 

children and others may be susceptible to accidental contact burns.  A physical barrier (safety screen) is 
required if there are at risk individuals in the house.  To restrict access to a fi replace or stove install an 
adjustable safety gate to keep toddlers, young children and other at risk individuals out of the room and 
away from hot surfaces.  Any safety screen, guard, or barrier removed for servicing an appliance must be 
replaced prior to operating the appliance.

•  Clothing or other fl ammable materials should not be placed on or near the appliance.

YOUR SAFETY

•  Have the venting system inspected annually by a qualifi ed installer for blockage and signs of deterioration.
•  To prevent injury, do not allow anyone who is unfamiliar with the stove to operate it.
•  To prevent injury, if the pilot or pilot and burners have gone out on their own, open the glass door and wait 

5 minutes to air out before attempting to relight the stove.

•  Always keep the area around these appliances clear of combustible material, gasoline and other fl ammable 

liquids and vapors.

•  These appliances should not be used as a drying rack for clothing or for hanging Christmas stockings/

decorations.

•  Due to the paint curing on the stove, a faint odor and slight smoking will likely be noticed when the stove is 

fi rst used.  Open a window until the smoking stops.

•  Do not use this appliance if any part has been under water.  Immediately call a qualifi ed service technician 

to inspect the appliance and to replace any part of the control system and any gas control which has been 
under water.

•  Do not abuse the glass by striking it or slamming the door shut.

DO NOT OPERATE WITH THE GLASS FRONT REMOVED, CRACKED OR BROKEN.  REPLACEMENT 

OF THE GLASS SHOULD BE DONE BY A LICENSED OR QUALIFIED SERVICE PERSON.

Содержание Clarity CL29.IPI













































Отзывы: