manualshive.com logo in svg

Blaze King Clarity CL29.IPI, Руководство по эксплуатации и установке

Поделиться
Скачать
Blaze King Clarity CL29.IPI Скачать руководство пользователя страница 31

180-CL29-SP v1.00

March 12, 2019

Page 31

Clarity CL29 SP

Fig.18

INSTALLATION

AIR SHUTTER ADJUSTMENT

The air shutter allows the amount of air coming 
into the burner to be adjusted in order to 
accommodate diff erent climates and venting 
arrangements.
1.  Lower the hinged door below the fi rebox.  

The air shutter adjustment lever is left of the 
valve. (

Fig.18

)

2.  Loosen the wing nut that locks the air 

shutter lever to the appliance.

3.  Start the pilot and then the burner.  Allow 

the appliance to operate for 15 minutes 
before making any air adjustments.

4.  The ideal fl ame will be blue at the base and 

light orange above.  If the fl ames are short 
and mostly blue, the fi replace is getting too 
much air.  Therefore, the air shutter should 
be closed slightly until the correct fl ames 
are achieved.  Slide the air shutter to the 
right to reduce the amount of air.

5.  Flames that are very orange, with tall, 

dark, stringy tips, are not getting enough 
air.  Therefore, the air shutter should be 
opened slightly until the desired fl ames are 
achieved.  Slide the air shutter to the left to 
increase the amount of air.

6.  Tighten air shutter lock wing nut.

BURNER FLAME APPEARANCE

The ideal fl ame will be blue at the base and 
light orange above.  If the fl ames are short 
and mostly blue, the fi replace is getting too 
much air, in this case the air shutter and/or the 
vent restrictor could be closed slightly until the 
correct fl ames are achieved.
Flames that are very orange, with tall dark, 
stringy tips, are not getting enough air.  
Therefore, the air shutter and/or the vent 
restrictor could be opened slightly until the 
correct fl ames are achieved.

Содержание Clarity CL29.IPI













































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды