Black+Decker BX330-B5, Оригинальное руководство пользователя

Страница: 4 / 28

4
ENGLISH (Original instructions)
• When blending, tighten the blender jar and blender jar
blade assembly and then use them on the main unit
base of the product. Do not install the blender jar blade
assembly on the unit alone.
• When dry grinding, tighten the dry grinding cup
(small/big) and dry grinding cup blade assembly and
then use them on the main unit base of the product. Do
not install the dry grinding cup blade assembly on the
unit alone.
• When blending, fully tighten the blender jar and the
blender jar blade assembly together to avoid water
leakage and to avoid the blender jar blade assembly
falling while running the appliance.
• When dry grinding, fully tighten the dry grinder cup
(small or big) and the dry grinding cup blade assembly
together to avoid water leakage and to avoid the dry
grinding cup blade assembly falling while running the
appliance.
• Never have the product run with an empty blender jar or
dry grinding cup (small or big) (there is no food material
in the cup) or overload.
• To avoid blender jar breakage, do not put too hot food
materials (permissible maximum temperature: 80˚C) in
the blender jar for processing.
• Make sure the food material level in the blender jar or
dry grinding cup (small or big) is not higher than the
maximum scale of the cup.
• After end of blending or dry grinding, do not dismantle
the blender jar or dry grinding cups (small or big)
immediately until the motor and the blending jar blade
assembly or dry grinding blade assembly have both
stopped and the power supply has been disconnected.
• Operate with the rated operating time strictly: Blend,
make soybean milk, dry grind continuously for 1 minute
at most each time. After end of any function above, stop
for 2 minutes to end a cycle. Stop for 15 to 20 minutes
after 5 successive cycles and start again after the motor
has cooled down. This practice can prolong life of the
product.
• If the product stops running in use, it is possibly caused
by temperature protection of the motor. Disconnect the
power supply for cooling and use the product 20 to 30
minutes later.
• To avoid heat caused deformation and damage, do not
disinfect any accessories in hot water above 80˚C or
microwave ovens. Materials of the parts in contact with
food materials should be clean, hygienic, reliable and in
compliance with relevant food hygiene certification.
• Do not process any fruits or vegetables with cores, hard
seeds or shells or thick skins until their cores, hard
seeds or shells or thick skins have been removed.
Inspection and repairs
• Before use, check the appliance for damaged or defective
parts. Check for breakage of parts, damage to switches
and any other conditions that may affect its operation.
• Do not use the appliance if any part is damaged or
defective.
• Have any damaged or defective parts repaired or
replaced by an authorised repair agent.
• Before use, check the power supply cord for signs of
damage, ageing and wear.
• Do not use the appliance if the power supply cord or
mains plug is damaged or defective.
• If the power supply cord or mains plug is damaged or
defective it must be repaired by an authorised repair
agent in order to avoid a hazard.
• Do not cut the power supply cord and do not attempt to
repair it yourself.
• Never attempt to remove or replace any parts other than
those specified in this manual.
Before first use
• Remove all packaging from the appliance.
• Clean the appliance before first use.
• Check that all parts are complete and not damaged.
Warning! The blades are sharp, handle with great care and
ensure that you unplug the appliance from power outlet
before assembling and removing parts.
Symbols on appliance
The following symbol is shown on the appliance.
Warning! Sharp blades, keep fingers out of
moving parts.
Features
1. Filler cup
2. Blender jar cover
3. Blender jar
4. Blender jar gasket
5. Blender jar blade assembly
6. Motor base
7. Control knob
8. Dry grinding cup (small)
9. Dry grinding cup (big)
10. Dry grinding cup gasket
11. Dry grinding cup blade assembly