Black+Decker BD40, Инструкция по эксплуатации

Страница: 7 / 68

7
ENGLISH
Minimum Gauge for Cord Sets
Volts Total length of cord in meters (m)
120 V - 127V 0 - 7 7 - 15 15 - 30 30 - 50
220 V 0 - 15 15 - 30 30 - 60 60 - 100
Ampere Rating
Minimal cross-sectional area of the
cord in milimeters (mm 2 )
More
Than
Not
More
Than
0 6 1,0 1,5 1,5 2,5
6 10 1,0 1,5 2,5 4,0
10 12 1,5 1,5 2,5 4,0
12 16 2,5 4,0 Not Recommended
•
Do not place any object on top of the charger or
place the charger on a soft surface that might block
the ventilation slots and result in excessive internal
heat.
Place the charger in a position away from any heat
source. The charger is ventilated through slots in the top
and the bottom of the housing.
• Do not operate the charger with a damaged cord
or plug.
• Do not operate the charger if it has received a sharp
blow, been dropped or otherwise damaged in any
way.
Take it to an authorized service center.
• Do not disassemble the charger; take it to an
authorized service center when service or repair
is required.
Incorrect reassembly may result in a risk of
electric shock, electrocution or fire.
• Disconnect the charger from the outlet before
attempting any cleaning. This will reduce the risk
of electric shock.
Removing the battery will not reduce
this risk.
• NEVER attempt to connect 2 chargers together.
• The charger is designed to operate on standard
household electrical power. Do not attempt to use
it on any other voltage.
This does not apply to the
vehicular charger.
WARNING: Shock hazard. Do not allow any liquid to
get inside the charger. Electric shock may result.
WARNING: Burn hazard. Do not submerge the
battery in any liquid or allow any liquid to enter the
battery. Never attempt to open the battery for any
reason. If the plastic housing of the battery breaks or
cracks, return to a service center for recycling.
CAUTION: Burn hazard. To reduce the risk of injury,
charge only BLACK+DECKERrechargeable batterys.
Other types of batteries may overheat and burst
resulting in personal injury and property damage.
NOTICE: Under certain conditions, with the charger
plugged into the power supply, the charger can
be shorted by foreign material. Foreign materials
of a conductive nature, such as, but not limited to,
grinding dust, metal chips, steel wool, aluminum
foil or any buildup of metallic particles should be
kept away from the charger cavities. Always unplug
the charger from the power supply when there is
no battery in the cavity. Unplug the charger before
attempting to clean.
Charger Cleaning Instructions
WARNING: Shock hazard. Disconnect the charger
from the AC outlet before cleaning. Dirt and grease
may be removed from the exterior of the charger
using a cloth or soft non-metallic brush. Do not use
water or any cleaning solutions.
Important Charging Notes
1. Longest life and best performance can be obtained
if the battery is charged when the air temperature is
between 65 °F and 75 °F (18 ° – 24 °C). DO NOT charge
the battery in an air temperature below +40 °F (+4.5 °C),
or above +104 °F (+40 °C). This is important and will
prevent serious damage to the battery.
2. The charger and battery may become warm to the
touch while charging. This is a normal condition, and
does not indicate a problem. To facilitate the cooling
of the battery after use, avoid placing the charger or
battery in a warm environment such as in a metal shed
or an uninsulated trailer.
3. If the battery does not charge properly:
a. Check operation of receptacle by plugging in a lamp
or other appliance;
b. Check to see if receptacle is connected to a light
switch which turns power off when you turn out the
lights;
c. Move the charger and battery to a location where
the surrounding air temperature is approximately
65 °F – 75 °F (18 ° – 24 °C);
d. If charging problems persist, take the tool, battery
and charger to your local service center.
4. The battery should be recharged when it fails to
produce sufficient power on jobs which were easily
done previously. DO NOT CONTINUE to use under these
conditions. Follow the charging procedure. You may
also charge a partially used pack whenever you desire
with no adverse effect on the battery.
5. Foreign materials of a conductive nature such as, but
not limited to, grinding dust, metal chips, steel wool,
aluminum foil, or any buildup of metallic particles
should be kept away from charger cavities. Always
unplug the charger from the power supply when there
is no battery in the cavity. Unplug the charger before
attempting to clean.
6. Do not freeze or immerse the charger in water or any
other liquid.
Storage Recommendations
1. The best storage place is one that is cool and dry, away
from direct sunlight and excess heat or cold.
2. For long storage, it is recommended to store a fully
charged battery in a cool dry place out of the charger
for optimal results.
NOTE: Batterys should not be stored completely depleted
of charge. The battery will need to be recharged before use.