Black Box LWE120A Скачать руководство пользователя страница 78

Страница: 78 / 88

724-746-5500 | blackbox.com

Page 78

Chapter 5: Navigate the Web Configurator

Figure 5-67. Captive Portal screen.

To enable Captive Portal, check “Captive Portal” and select the VAP network needed for captive portal.

Radius Settings

Primary Radius Server: Enter the name or IP address of the primary radius server.

Secondary Radius Server: Enter the name or IP address of the secondary radius server if any.

Radius Auth Port: Enter the port number for authentication.

Radius Acct Port: Enter the port number for billing.

Radius Shared Secret: Enter the secret key of the radius server .

Radius NAS ID: Enter the name of the radius server if any.

Radius Administrative-User

Radius Admin Username: Enter the username of the Radius Administrator.

Radius Admin Password: Enter the password of the Radius Administrator.

Captive Portal

UAM Portal URL: Enter the address of the UAM portal server.

UAM Secret: Enter the secret password between the redirect URL and the Hotspot.

WDS Settings

Extend the range of your network without having to use cables to link the Access Points by using the Wireless Distribution System
(WDS): Simply put, you can link the Access Points wirelessly. Open “WDS Settings” in “Wireless” as shown next:

Содержание LWE120A

























































































Результаты поиска

Содержание LWE120A

Отзывы:

Похожие инструкции для LWE120A

Бренды по названию

Популярные бренды

Black Box LWE120A, Руководство пользователя

Результаты поиска

Содержание LWE120A

Отзывы:

Похожие инструкции для LWE120A

Бренды по названию

Популярные бренды