Black Box LWE120A Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 88

background image

724-746-5500 | blackbox.com

Page 9

Chapter 2: Overview

2. Overview
2.1 Introduction

The Wireless Ethernet Extender is a 2x2 outdoor access point. The LWE120A operates at 2.4-GHz band. Ideally suited for SMB or
hotspot networks, this breakthrough innovation provides superior Wi-Fi network solutions at significantly lower cost.

In addition, the easy-to-install Wireless Ethernet Extender is also a high-performance last-mile broadband solution that provides
reliable wireless network coverage for outdoor broadband application.

While operating as access point, the Wireless Ethernet Extender also provides centralized management and monitoring of all the
VAC-managed APs on the network. In addition, the easy-to-install Wireless Ethernet Extender is also a high-performance last-mile
broadband solution that provides reliable wireless network coverage for outdoor broadband application.

2.2 Features

• Centralized configuration control for your network.

• Compliant with IEEE 802.11n standard.

• Support passive PoE supplied with 24V.

• High reliable watertight housing endures almost any harsh environments.

• Three management modes including AC, AC+Thin AP, Thin AP and Fat AP.

• Four wireless operation modes in FAT AP mode including AP, Wireless Client, WDS and AP Repeater.

• Up to 8 BSSIDs available for service deployment.

• Support encryption: 64/128/152-bit WEP and 802.1X, WPA, WPA2, WPA & WPA2, WPA-PSK, WPA2-PSK, and WPA-PSK &

WPA2-PSK.

• User-friendly Web and SNMP-based management interface.

2.3 What’s Included

Your package should contain the following items. If anything is missing or damaged, contact Black Box Technical Support
at 724-746-5500 or [email protected].

The LWE120A and LWE120AE packages contain the following items:

• (1) IEEE 802.11n Wireless Ethernet Extender

• (1) pole-mounting ring

• (1) 24-VDC power cord and PoE injector

• (1) ferrite suppression core

• (1) grounding wire

• A printed quick installation guide

The LWE120A-KIT and LWE120AE-KIT packages contain two each of the items listed above for LWE120A and LWE120AE.

To download the user manual from the Web site:

1. Go to www.blackbox.com

2. Enter the part number (LWE120A) in the search box:

3. Click on the “Resources” tab on the product page, and select the document you wish to download.

NOTE: Users MUST use the power cord and PoE injector shipped in the box with the Wireless Ethernet Extender. Using other

options will damage the unit.

«
...
7
8
9
10
11
...
»

Содержание LWE120A

























































































Отзывы:

Нет отзывов

Похожие инструкции для LWE120A

Бренд: D-Link Страницы: 104

Бренд: Extron electronics Страницы: 2

DL-1H1A1U-WPKT-W

Бренд: DigitaLinx Страницы: 8

51101B - Single-Serve Blender With Travel...

Бренд: Hamilton Beach Страницы: 6

Bullet Blender 50-DX

Бренд: Next Advance Страницы: 8

Бренд: Lindy Страницы: 2

Бренд: Mircom Страницы: 2

Бренд: Asus Страницы: 119

Continuum EaganMatrix

Бренд: Haken Audio Страницы: 6

Бренд: Hailink Страницы: 6

Бренд: Omcan Страницы: 4

Бренд: Zelmer Страницы: 30

Бренд: Zelmer Страницы: 46

Бренд: zBoost Страницы: 12

Бренд: Termozeta Страницы: 16

Smart IP Extender

Бренд: Minicom Страницы: 68

Бренд: Braun Страницы: 6

Бренд: STI Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды