Black Box LWE120A Скачать руководство пользователя страница 74 | Manualshive

Страница: 74 / 88

background image

724-746-5500 | blackbox.com

Page 74

Chapter 5: Navigate the Web Configurator

Figure 5-64. VLAN screen.

Advanced Settings

Open “Advanced Settings” in “Wireless” to make advanced wireless settings.

A-MPDU/A-MSDU Aggregation

The data rate of your AP except wireless client mode could be enhanced greatly with this option enabled; however, if your
wireless clients don’t support A-MPDU/A-MSDU aggregation, we do not recommend to enabling it.

Short GI

Under 802.11n mode, enable it to obtain a better data rate if there is no negative compatibility issue.

RTS Threshold

The Wireless Ethernet Extender sends RTS (Request to Send) frames to certain receiving station and negotiates the sending of a
data frame. After receiving an RTS, that STA responds with a CTS (Clear to Send) frame to acknowledge the right to start
transmission. The setting range is 0 to 2346 bytes. Setting it too low may result in poor network performance. We recommend
leaving it at its default of 2346.

Fragmentation Length

Specify the maximum byte size for a packet before data is fragmented into multiple packets. Setting it too low may result in poor
network performance. We recommend leaving it at its default of 2346.

Beacon Interval

Specify the frequency interval to broadcast packets. Enter a value between 20 and 1024.

DTIM Interval

DTIM, which stands for Delivery Traffic Indication Message, is contained in the data packets. It is for enhancing the wireless
transmission efficiency. The default is set to 1. Enter a value between 1 and 255.

Preamble Type

This defines some details on the 802.11 physical layer. “Long” and “Auto” are available.

«
...
72
73
74
75
76
...
»

Содержание LWE120A

























































































Отзывы:

Нет отзывов

Похожие инструкции для LWE120A

100BASE-FX DISTANCE EXTENDER

Бренд: 3Com Страницы: 2

Бренд: Tripp Lite Страницы: 2

Бренд: Calphalon Страницы: 20

Бренд: tams elektronik Страницы: 40

Бренд: Nikrans Страницы: 21

Бренд: Hung Страницы: 7

Бренд: Cables to Go Страницы: 6

Бренд: Westermo Страницы: 18

Бренд: J-Tech Digital Страницы: 36

Бренд: Multi-Link Страницы: 20

PB7900 MultiBlender

Бренд: Sunbeam Страницы: 27

Бренд: SMART-AVI Страницы: 2

SoloCAT Ultra MAX

Бренд: Zektor Страницы: 8

Бренд: Icron Страницы: 2

XTENDEX ST-C6DVIA-IR-R-300

Бренд: NTI Страницы: 12

Бренд: Wilson Electronics Страницы: 8

Бренд: Wilson Electronics Страницы: 16

Бренд: Graco Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды