Black Box LWE120A Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 88

background image

724-746-5500 | blackbox.com

Page 12

Chapter 2: Overview

Table 2-1. LED indicators.

LED

Color

Status

Description

PWR

Green

ON

The device is powered on.

OFF

The device is not receiving power.

LAN

Green

ON

The device has an Ethernet connection.

OFF

The device has no Ethernet connection.

Blinking

Transmitting/receiving Ethernet packets.

WLAN

Green

ON

The WLAN is active.

OFF

The WLAN is inactive.

Blinking

Transmitting/receiving wireless packets.

Signal

Green

3 LED ON

The signal strength is excellent.

2 LED ON

The signal strength is good.

1 LED ON

The signal strength is weak.

2.5 Typical Management Scenario

This section describes the typical management of Wireless Ethernet Extender. By default, it is set to thin AP mode (managed AP)
which allows it to be managed by the Wireless Ethernet Extender in AC mode. The following figure illustrates a VAC wireless
network.

LWE120A

HVAC

LWE120A

HVAC

HVAC

HVAC

LWE120A

LWE121A

operating as an

access point

Figure 2-6. Typical management scenario.

«
...
10
11
12
13
14
...
»

Содержание LWE120A

























































































Отзывы:

Нет отзывов

Похожие инструкции для LWE120A

Бренд: Oster Страницы: 34

Бренд: on networks Страницы: 12

Бренд: DigitaLinx Страницы: 6

Бренд: Hamilton Beach Страницы: 16

Бренд: Calphalon Страницы: 10

Бренд: StarTech.com Страницы: 10

Бренд: Atlona Страницы: 10

Бренд: Novis Страницы: 144

Бренд: UFESA Страницы: 52

Бренд: Zigen Страницы: 18

Бренд: Indesit Страницы: 13

Бренд: Ginnys Страницы: 7

Бренд: Westell Technologies Страницы: 50

Sage Boss To Go Grind & Mill

Бренд: Heston Blumenthal Страницы: 4

Бренд: Bamix Страницы: 190

Tom Dickson Extreme Blender

Бренд: Blendtec Страницы: 20

Бренд: CRAIN Страницы: 2

Бренд: Jupiter Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды