Black Box LWE120A Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 88

background image

724-746-5500 | blackbox.com

Page 22

Chapter 4: Quick Setup Tutorial

4.2 Configure the AC+Thin AP mode

To operate as AC+Thin AP mode, go to Basic Settings. From the Device Mode drop-down list, select “Virtual AC” mode. To use
the extender as a virtual controller and access point concurrently, select “Virtual AC + Thin AP” mode. Then assign an IP address
to the Wireless Ethernet Extender and specify subnet mask, gateway, and DNS address, respectively. Press “Apply” and wait for
about 50 seconds to take effect.

Figure 4-3. Basic settings screen.

NOTE: AC+ Thin AP mode allows the Wireless Ethernet Extender to operate as access controller and thin AP at the same time.

NOTE: To operate the extender as a standalone Access Point, wireless client, or bridge, select FAT AP from device mode.

For Virtual Cont Thin AP mode, if you need to configure the wireless settings for the Wireless Ethernet Extender, especially
SSID and encryption method, go to Wireless Settings —> Wireless Networks and click on “#1 Wireless SSID” for configuration.
Click “Save” to save the settings.

Figure 4-4. Wirelss Networks screen.

«
...
20
21
22
23
24
...
»

Содержание LWE120A

























































































Отзывы:

Нет отзывов

Похожие инструкции для LWE120A

PRO MEGAMIX HPB300

Бренд: Waring Страницы: 8

Бренд: Waring Страницы: 7

Бренд: Oster Страницы: 40

Бренд: Skymsen Страницы: 16

Бренд: Patton Страницы: 59

Бренд: Hall Research Technologies Страницы: 8

Бренд: cable matters Страницы: 52

Бренд: Gefen Страницы: 17

ADDERLINK AV200 Series

Бренд: ADDER Страницы: 2

Бренд: DCU Tecnologic Страницы: 2

Бренд: SC&T Страницы: 17

RE270K / RE370K

Бренд: TP-Link Страницы: 34

Бренд: Genie Страницы: 6

Бренд: HDanywhere Страницы: 9

Бренд: HDanywhere Страницы: 13

Бренд: HDanywhere Страницы: 22

L-8SDI-FE-HD-RX

Бренд: Questtel Страницы: 15

Бренд: Nutri Ninja Страницы: 40

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды