Black Box LRA2900A Скачать руководство пользователя

Страница: 65 / 66

5 • Troubleshooting and maintenance

Model LRA2900A RAS Getting Started Guide

Maintenance

15. Click on

HOME

under the

Configuration Menu

, then click on the

Hard Reset

button under

Immediate

Actions

Note

Do not

select

Record Current Configuration

after importing configu-

ration parameters.

Completing the installation

This section verifies that the RAS is fully operational.

1. Temporarily disconnect the male ends of both power cords from the power distribution strip or to a wall

outlet. Wait 30 seconds, then plug the power cords in again.

2. Verify that the green POWER LED is lit. If the POWER LED is flashing green, refer to Chapter 5, “Trou-

bleshooting and maintenance”.

3. Verify that the Link 1 Frame LED illuminates, indicating that the RAS is synchronizing with the T1/E1/

PRI signal.

4. Verify that after 5 seconds, the Link A Error LED begins flashing, indicating that the RAS is satisfied with

the quality of the T1/E1/PRI signal.

5. Verify that after 10 seconds, the Link A Error LED extinguishes, indicating that the RAS is satisfied with

the network signal and that the link is ready for use.

6. There are two LEDs on the RAS 10/100 Ethernet port: a yellow LED that indicates link status and activ-

ity, and a green LED that indicates line speed.

Verify that the yellow LED is either flashing yellow (meaning that packets are being received at the Ether-
net port) or solid yellow (meaning that the link is valid but no packets are being received).

The RAS is operational.

Содержание LRA2900A


































































Результаты поиска

Содержание LRA2900A

Отзывы:

Похожие инструкции для LRA2900A

Бренды по названию

Популярные бренды

Black Box LRA2900A, Руководство по началу работы

Результаты поиска

Содержание LRA2900A

Отзывы:

Похожие инструкции для LRA2900A

Бренды по названию

Популярные бренды