Black & Decker HD555, Инструкция по эксплуатации

Страница: 8 / 12

8
●
简体中文
4)
将闲置不用的电动工具贮存在儿童所及范围之
外，并且不要让不熟悉电动工具或对这些说明
不了解的人操作电动工具。
电动工具在未经培
训的用户手中是危险的。
5)
保养电动工具。检查运动件是否调整到位或卡
住，检查零件破损情况和影响电动工具运行的
其他状况。如有损坏，电动工具应在使用前修
理好。
许多事故由维护不良的电动工具引发。
6)
保持切削刀具锋利和清洁。 保养良好的有锋利
切削刃的刀具不易卡住而且容易控制。
7)
按照使用说明书，考虑作业条件和进行的作业
来使用电动工具、附件和工具的刀头等。 将电
动工具用于那些与其用途不符的操作可能会
导致危险。
e
)
维修
1)
将你的电动工具送交专业维修人员，使用同样
的备件进行修理。 这样将确保所维修的电动工
具的安全性。
电钻专用警告语 ：
← 使用冲击电钻时要戴好耳罩。 暴露在噪声中会
引起听力损伤。
← 使用随工具提供的辅助手柄。 操作失手会引起
人身伤害。
← 当在钻削附件可能触及暗线或其自身软线之
处进行操作时，要通过绝缘握持面来握持工
具。
钻削附件碰到带电导线会使工具外露的金
属零件带电从而使操作者受到电击。
← 请使用夹具或采取其它可行方法，将工件可靠
地固定在稳定的平台上。
手持或用身体顶住工
件都是不稳定的，会导致操作失控。
← 在墙上、地板或天花板上钻孔之前，请检查电
线和钢管位置。
←
不要在钻孔后立刻碰触可能还带热的钻头尖端。
6
. 电气安全
本工具采用双重绝缘，因此无需接地线。
请务必检查电源电压是否与铭牌一致。
警告！ 如电源线损坏，必须由制造商、
BLACK+DECKER
授权服务中心或具备同
等资格的人士进行更换，以避免事故或
人身伤亡。如电源线由具备同等资格但
未经
BLACK+DECKER
授权的人士更换，
则产品质保将无效。
7
. 工具上的标签
您的工具上可能包含下列符号 ：
4
•
ENGLISH
4 • ENGLISH
making any adjustments, changing accessories,
or storing power tools. Such preventive safety measures
reduce the risk of starting the power tool accidentally.
d. Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the power
tool or these instructions to operate the power
tool. Power tools are dangerous in the hands
of untrained users.
e. Maintain power tools. Check for misalignment
or binding of moving parts, breakage of parts and
any other condition that may affect the power
tools operation. If damaged, have the power tool
repaired before use. Many accidents are caused by
poorly maintained power tools.
f. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
5. Service
a. Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
6. Electrical safety
Your tool is double insulated; therefore no earth
wire is required. Always check that the main voltage
corresponds to the voltage on the rating plate.
Warning! If the power cord is damaged, it must
be replaced by the manufacturer, authorized
BLACK+DECKER Service Center or an equally
qualified person in order to avoid damage or
injury. If the power cord is replaced by an equally
7. Labels on tool
The label on your tool may include the following symbols:
FEATURES (Fig. A)
1. Variable speed switch
2. Lock-on button
3. Forward/reverse slider
4. Drilling mode selector
5. Chuck
6. Depth stop
7. Side handle
ADDITIONAL SAFETY INSTRUCTIONS
FOR HAMMER DRILL
f
Wear ear protectors with impact drills. Exposure to
noise can cause hearing loss.
f
Use auxiliary handles supplied with the tool. Loss
of control can cause personal injury.
f
Hold power tool by insulated gripping surfaces
when performing an operation where the cutting
tool may contact hidden wiring or its own cord.
Contact with a “live” wire will also make exposed metal
parts of the power tool “live” and shock the operator.
f
Use clamps or another practical way to secure
and support the workpiece to a stable platform.
Holding the work by hand or against your body leaves
it unstable and may lead to loss of control.
f
Before drilling into walls, floors or ceilings check for
the location of wiring and pipes.
f
Avoid touching the tip of a drill bit just after drilling, as
it may be hot
ASSAMBLY
Warning! Before assembly, make sure that the tool is
switched off and unplugged.
Fitting the side handle and depth stop (Fig. B)
Turn the grip counterclockwise until you can slide the
side handle (7) onto the front of the tool as shown.
f
Rotate the side handle into the desired position.
f
Insert the depth stop (6) into the mounting hole as
shown.
f
Set the drilling depth as described below.
f
Tighten the side handle by turning the grip clockwise.
Fitting a drill bit or screwdriver bit
Keyed chuck (Fig. C)
f
Open the chuck by turning the sleeve (9)
counterclockwise.
f
Insert the bit shaft (8) into the chuck.
f
Insert the chuck key (10) into each hole (11) in the side
of the chuck and turn clockwise until tight.
Removing and refitting the chuck (Fig. D)
f
Open the chuck as far as possible.
f
Remove the chuck retaining screw, located in the
chuck, by turning it clockwise using a screwdriver.
f
Tighten an Allen key into the chuck and strike it with
a hammer as shown.
f
Remove the Allen key.
f
Remove the chuck by turning it counterclockwise.
f
To refit the chuck, screw it onto the spindle and secure
it with the chuck retaining screw.
Read
Instructions
Manual
Use Eye
Protection
Use Ear
Protection
V ........ Volts
A ........ Amperes
Hz ....... Hertz
W ........ Watts
min ..... minutes
..... Alternating
Current
..... Direct
Current
n
0
....... No-Load
Speed
...... Class II
Construction
.... Earthing
Terminal
.... Safety Alert
Symbol
.../min.. Revolutions
or Recipro-
cation per
minute
qualified person, but not authorized by
BLACK+DECKER, the warranty will not be valid.
4
•
ENGLISH
4 • ENGLISH
making any adjustments, changing accessories,
or storing power tools. Such preventive safety measures
reduce the risk of starting the power tool accidentally.
d. Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the power
tool or these instructions to operate the power
tool. Power tools are dangerous in the hands
of untrained users.
e. Maintain power tools. Check for misalignment
or binding of moving parts, breakage of parts and
any other condition that may affect the power
tools operation. If damaged, have the power tool
repaired before use. Many accidents are caused by
poorly maintained power tools.
f. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
5. Service
a. Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
6. Electrical safety
Your tool is double insulated; therefore no earth
wire is required. Always check that the main voltage
corresponds to the voltage on the rating plate.
Warning! If the power cord is damaged, it must
be replaced by the manufacturer, authorized
BLACK+DECKER Service Center or an equally
qualified person in order to avoid damage or
injury. If the power cord is replaced by an equally
7. Labels on tool
The label on your tool may include the following symbols:
FEATURES (Fig. A)
1. Variable speed switch
2. Lock-on button
3. Forward/reverse slider
4. Drilling mode selector
5. Chuck
6. Depth stop
7. Side handle
ADDITIONAL SAFETY INSTRUCTIONS
FOR HAMMER DRILL
f
Wear ear protectors with impact drills. Exposure to
noise can cause hearing loss.
f
Use auxiliary handles supplied with the tool. Loss
of control can cause personal injury.
f
Hold power tool by insulated gripping surfaces
when performing an operation where the cutting
tool may contact hidden wiring or its own cord.
Contact with a “live” wire will also make exposed metal
parts of the power tool “live” and shock the operator.
f
Use clamps or another practical way to secure
and support the workpiece to a stable platform.
Holding the work by hand or against your body leaves
it unstable and may lead to loss of control.
f
Before drilling into walls, floors or ceilings check for
the location of wiring and pipes.
f
Avoid touching the tip of a drill bit just after drilling, as
it may be hot
ASSAMBLY
Warning! Before assembly, make sure that the tool is
switched off and unplugged.
Fitting the side handle and depth stop (Fig. B)
Turn the grip counterclockwise until you can slide the
side handle (7) onto the front of the tool as shown.
f
Rotate the side handle into the desired position.
f
Insert the depth stop (6) into the mounting hole as
shown.
f
Set the drilling depth as described below.
f
Tighten the side handle by turning the grip clockwise.
Fitting a drill bit or screwdriver bit
Keyed chuck (Fig. C)
f
Open the chuck by turning the sleeve (9)
counterclockwise.
f
Insert the bit shaft (8) into the chuck.
f
Insert the chuck key (10) into each hole (11) in the side
of the chuck and turn clockwise until tight.
Removing and refitting the chuck (Fig. D)
f
Open the chuck as far as possible.
f
Remove the chuck retaining screw, located in the
chuck, by turning it clockwise using a screwdriver.
f
Tighten an Allen key into the chuck and strike it with
a hammer as shown.
f
Remove the Allen key.
f
Remove the chuck by turning it counterclockwise.
f
To refit the chuck, screw it onto the spindle and secure
it with the chuck retaining screw.
Read
Instructions
Manual
Use Eye
Protection
Use Ear
Protection
V ........ Volts
A ........ Amperes
Hz ....... Hertz
W ........ Watts
min ..... minutes
..... Alternating
Current
..... Direct
Current
n
0
....... No-Load
Speed
...... Class II
Construction
.... Earthing
Terminal
.... Safety Alert
Symbol
.../min.. Revolutions
or Recipro-
cation per
minute
qualified person, but not authorized by
BLACK+DECKER, the warranty will not be valid.
参阅说
明手册
使用护
目设备
使用护
耳设备
V
��������伏特
A
��������安培
Hz
������赫兹
W
�������瓦特
min
�����分钟
������������交流电
������������直流电
n
0
�������空载转速
������������
II
级结构
������������接地终端
������������安全警
告标识
���/
min
��每分钟
旋转或
往复次
数
功能部件（图
A
）
1
� 变速开关
2
� 锁定按钮
3
� 正 / 反转滑块
4
� 钻孔模式选择器
5
� 夹头
6
� 限深器
7
� 侧手柄
组装
警告！ 组装前，请确保关闭工具电源并拔下
工具插头。
安装侧手柄和限深器（图
B
）
逆时针转动手柄直到您可以将侧手柄 (
7
) 滑动至工
具正面为止，如图所示。
← 将侧手柄转入所需位置。
← 将深度尺 (
6
) 插入安装孔，如图所示。
← 按照以下说明设置钻孔深度。
← 通过顺时针转动手柄转紧侧手柄。
安装钻头或螺丝起子头带键夹头（图
C
）
← 通过逆时针转动套管 (
9
) 打开夹头。
← 将钻头轴 (
8
) 插入夹头。
← 将夹头栓 (
10
) 插入夹头侧面的每个插孔 (
11
)，
然后顺时针转紧。
卸下及装回夹头（图
D
）
← 将夹头打开到最大位置。
← 用螺丝起子顺时针转动夹头的固定螺钉将夹
头取出。
← 将内六角起子转紧到夹头内，然后用锤子打
击，如图所示。
← 取出内六角起子。
← 逆时针转动夹头将它取出。
← 要装回夹头，可将它旋入主轴，然后用夹头固
定螺钉将它锁紧。
4
•
ENGLISH
4 • ENGLISH
making any adjustments, changing accessories,
or storing power tools. Such preventive safety measures
reduce the risk of starting the power tool accidentally.
d. Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the power
tool or these instructions to operate the power
tool. Power tools are dangerous in the hands
of untrained users.
e. Maintain power tools. Check for misalignment
or binding of moving parts, breakage of parts and
any other condition that may affect the power
tools operation. If damaged, have the power tool
repaired before use. Many accidents are caused by
poorly maintained power tools.
f. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
5. Service
a. Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
6. Electrical safety
Your tool is double insulated; therefore no earth
wire is required. Always check that the main voltage
corresponds to the voltage on the rating plate.
Warning! If the power cord is damaged, it must
be replaced by the manufacturer, authorized
BLACK+DECKER Service Center or an equally
qualified person in order to avoid damage or
injury. If the power cord is replaced by an equally
7. Labels on tool
The label on your tool may include the following symbols:
FEATURES (Fig. A)
1. Variable speed switch
2. Lock-on button
3. Forward/reverse slider
4. Drilling mode selector
5. Chuck
6. Depth stop
7. Side handle
ADDITIONAL SAFETY INSTRUCTIONS
FOR HAMMER DRILL
f
Wear ear protectors with impact drills. Exposure to
noise can cause hearing loss.
f
Use auxiliary handles supplied with the tool. Loss
of control can cause personal injury.
f
Hold power tool by insulated gripping surfaces
when performing an operation where the cutting
tool may contact hidden wiring or its own cord.
Contact with a “live” wire will also make exposed metal
parts of the power tool “live” and shock the operator.
f
Use clamps or another practical way to secure
and support the workpiece to a stable platform.
Holding the work by hand or against your body leaves
it unstable and may lead to loss of control.
f
Before drilling into walls, floors or ceilings check for
the location of wiring and pipes.
f
Avoid touching the tip of a drill bit just after drilling, as
it may be hot
ASSAMBLY
Warning! Before assembly, make sure that the tool is
switched off and unplugged.
Fitting the side handle and depth stop (Fig. B)
Turn the grip counterclockwise until you can slide the
side handle (7) onto the front of the tool as shown.
f
Rotate the side handle into the desired position.
f
Insert the depth stop (6) into the mounting hole as
shown.
f
Set the drilling depth as described below.
f
Tighten the side handle by turning the grip clockwise.
Fitting a drill bit or screwdriver bit
Keyed chuck (Fig. C)
f
Open the chuck by turning the sleeve (9)
counterclockwise.
f
Insert the bit shaft (8) into the chuck.
f
Insert the chuck key (10) into each hole (11) in the side
of the chuck and turn clockwise until tight.
Removing and refitting the chuck (Fig. D)
f
Open the chuck as far as possible.
f
Remove the chuck retaining screw, located in the
chuck, by turning it clockwise using a screwdriver.
f
Tighten an Allen key into the chuck and strike it with
a hammer as shown.
f
Remove the Allen key.
f
Remove the chuck by turning it counterclockwise.
f
To refit the chuck, screw it onto the spindle and secure
it with the chuck retaining screw.
Read
Instructions
Manual
Use Eye
Protection
Use Ear
Protection
V ........ Volts
A ........ Amperes
Hz ....... Hertz
W ........ Watts
min ..... minutes
..... Alternating
Current
..... Direct
Current
n
0
....... No-Load
Speed
...... Class II
Construction
.... Earthing
Terminal
.... Safety Alert
Symbol
.../min.. Revolutions
or Recipro-
cation per
minute
qualified person, but not authorized by
BLACK+DECKER, the warranty will not be valid.
4
•
ENGLISH
4 • ENGLISH
making any adjustments, changing accessories,
or storing power tools. Such preventive safety measures
reduce the risk of starting the power tool accidentally.
d. Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the power
tool or these instructions to operate the power
tool. Power tools are dangerous in the hands
of untrained users.
e. Maintain power tools. Check for misalignment
or binding of moving parts, breakage of parts and
any other condition that may affect the power
tools operation. If damaged, have the power tool
repaired before use. Many accidents are caused by
poorly maintained power tools.
f. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
5. Service
a. Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
6. Electrical safety
Your tool is double insulated; therefore no earth
wire is required. Always check that the main voltage
corresponds to the voltage on the rating plate.
Warning! If the power cord is damaged, it must
be replaced by the manufacturer, authorized
BLACK+DECKER Service Center or an equally
qualified person in order to avoid damage or
injury. If the power cord is replaced by an equally
7. Labels on tool
The label on your tool may include the following symbols:
FEATURES (Fig. A)
1. Variable speed switch
2. Lock-on button
3. Forward/reverse slider
4. Drilling mode selector
5. Chuck
6. Depth stop
7. Side handle
ADDITIONAL SAFETY INSTRUCTIONS
FOR HAMMER DRILL
f
Wear ear protectors with impact drills. Exposure to
noise can cause hearing loss.
f
Use auxiliary handles supplied with the tool. Loss
of control can cause personal injury.
f
Hold power tool by insulated gripping surfaces
when performing an operation where the cutting
tool may contact hidden wiring or its own cord.
Contact with a “live” wire will also make exposed metal
parts of the power tool “live” and shock the operator.
f
Use clamps or another practical way to secure
and support the workpiece to a stable platform.
Holding the work by hand or against your body leaves
it unstable and may lead to loss of control.
f
Before drilling into walls, floors or ceilings check for
the location of wiring and pipes.
f
Avoid touching the tip of a drill bit just after drilling, as
it may be hot
ASSAMBLY
Warning! Before assembly, make sure that the tool is
switched off and unplugged.
Fitting the side handle and depth stop (Fig. B)
Turn the grip counterclockwise until you can slide the
side handle (7) onto the front of the tool as shown.
f
Rotate the side handle into the desired position.
f
Insert the depth stop (6) into the mounting hole as
shown.
f
Set the drilling depth as described below.
f
Tighten the side handle by turning the grip clockwise.
Fitting a drill bit or screwdriver bit
Keyed chuck (Fig. C)
f
Open the chuck by turning the sleeve (9)
counterclockwise.
f
Insert the bit shaft (8) into the chuck.
f
Insert the chuck key (10) into each hole (11) in the side
of the chuck and turn clockwise until tight.
Removing and refitting the chuck (Fig. D)
f
Open the chuck as far as possible.
f
Remove the chuck retaining screw, located in the
chuck, by turning it clockwise using a screwdriver.
f
Tighten an Allen key into the chuck and strike it with
a hammer as shown.
f
Remove the Allen key.
f
Remove the chuck by turning it counterclockwise.
f
To refit the chuck, screw it onto the spindle and secure
it with the chuck retaining screw.
Read
Instructions
Manual
Use Eye
Protection
Use Ear
Protection
V ........ Volts
A ........ Amperes
Hz ....... Hertz
W ........ Watts
min ..... minutes
..... Alternating
Current
..... Direct
Current
n
0
....... No-Load
Speed
...... Class II
Construction
.... Earthing
Terminal
.... Safety Alert
Symbol
.../min.. Revolutions
or Recipro-
cation per
minute
qualified person, but not authorized by
BLACK+DECKER, the warranty will not be valid.
4
•
ENGLISH
4 • ENGLISH
making any adjustments, changing accessories,
or storing power tools. Such preventive safety measures
reduce the risk of starting the power tool accidentally.
d. Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the power
tool or these instructions to operate the power
tool. Power tools are dangerous in the hands
of untrained users.
e. Maintain power tools. Check for misalignment
or binding of moving parts, breakage of parts and
any other condition that may affect the power
tools operation. If damaged, have the power tool
repaired before use. Many accidents are caused by
poorly maintained power tools.
f. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
5. Service
a. Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
6. Electrical safety
Your tool is double insulated; therefore no earth
wire is required. Always check that the main voltage
corresponds to the voltage on the rating plate.
Warning! If the power cord is damaged, it must
be replaced by the manufacturer, authorized
BLACK+DECKER Service Center or an equally
qualified person in order to avoid damage or
injury. If the power cord is replaced by an equally
7. Labels on tool
The label on your tool may include the following symbols:
FEATURES (Fig. A)
1. Variable speed switch
2. Lock-on button
3. Forward/reverse slider
4. Drilling mode selector
5. Chuck
6. Depth stop
7. Side handle
ADDITIONAL SAFETY INSTRUCTIONS
FOR HAMMER DRILL
f
Wear ear protectors with impact drills. Exposure to
noise can cause hearing loss.
f
Use auxiliary handles supplied with the tool. Loss
of control can cause personal injury.
f
Hold power tool by insulated gripping surfaces
when performing an operation where the cutting
tool may contact hidden wiring or its own cord.
Contact with a “live” wire will also make exposed metal
parts of the power tool “live” and shock the operator.
f
Use clamps or another practical way to secure
and support the workpiece to a stable platform.
Holding the work by hand or against your body leaves
it unstable and may lead to loss of control.
f
Before drilling into walls, floors or ceilings check for
the location of wiring and pipes.
f
Avoid touching the tip of a drill bit just after drilling, as
it may be hot
ASSAMBLY
Warning! Before assembly, make sure that the tool is
switched off and unplugged.
Fitting the side handle and depth stop (Fig. B)
Turn the grip counterclockwise until you can slide the
side handle (7) onto the front of the tool as shown.
f
Rotate the side handle into the desired position.
f
Insert the depth stop (6) into the mounting hole as
shown.
f
Set the drilling depth as described below.
f
Tighten the side handle by turning the grip clockwise.
Fitting a drill bit or screwdriver bit
Keyed chuck (Fig. C)
f
Open the chuck by turning the sleeve (9)
counterclockwise.
f
Insert the bit shaft (8) into the chuck.
f
Insert the chuck key (10) into each hole (11) in the side
of the chuck and turn clockwise until tight.
Removing and refitting the chuck (Fig. D)
f
Open the chuck as far as possible.
f
Remove the chuck retaining screw, located in the
chuck, by turning it clockwise using a screwdriver.
f
Tighten an Allen key into the chuck and strike it with
a hammer as shown.
f
Remove the Allen key.
f
Remove the chuck by turning it counterclockwise.
f
To refit the chuck, screw it onto the spindle and secure
it with the chuck retaining screw.
Read
Instructions
Manual
Use Eye
Protection
Use Ear
Protection
V ........ Volts
A ........ Amperes
Hz ....... Hertz
W ........ Watts
min ..... minutes
..... Alternating
Current
..... Direct
Current
n
0
....... No-Load
Speed
...... Class II
Construction
.... Earthing
Terminal
.... Safety Alert
Symbol
.../min.. Revolutions
or Recipro-
cation per
minute
qualified person, but not authorized by
BLACK+DECKER, the warranty will not be valid.
4
•
ENGLISH
4 • ENGLISH
making any adjustments, changing accessories,
or storing power tools. Such preventive safety measures
reduce the risk of starting the power tool accidentally.
d. Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the power
tool or these instructions to operate the power
tool. Power tools are dangerous in the hands
of untrained users.
e. Maintain power tools. Check for misalignment
or binding of moving parts, breakage of parts and
any other condition that may affect the power
tools operation. If damaged, have the power tool
repaired before use. Many accidents are caused by
poorly maintained power tools.
f. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
5. Service
a. Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
6. Electrical safety
Your tool is double insulated; therefore no earth
wire is required. Always check that the main voltage
corresponds to the voltage on the rating plate.
Warning! If the power cord is damaged, it must
be replaced by the manufacturer, authorized
BLACK+DECKER Service Center or an equally
qualified person in order to avoid damage or
injury. If the power cord is replaced by an equally
7. Labels on tool
The label on your tool may include the following symbols:
FEATURES (Fig. A)
1. Variable speed switch
2. Lock-on button
3. Forward/reverse slider
4. Drilling mode selector
5. Chuck
6. Depth stop
7. Side handle
ADDITIONAL SAFETY INSTRUCTIONS
FOR HAMMER DRILL
f
Wear ear protectors with impact drills. Exposure to
noise can cause hearing loss.
f
Use auxiliary handles supplied with the tool. Loss
of control can cause personal injury.
f
Hold power tool by insulated gripping surfaces
when performing an operation where the cutting
tool may contact hidden wiring or its own cord.
Contact with a “live” wire will also make exposed metal
parts of the power tool “live” and shock the operator.
f
Use clamps or another practical way to secure
and support the workpiece to a stable platform.
Holding the work by hand or against your body leaves
it unstable and may lead to loss of control.
f
Before drilling into walls, floors or ceilings check for
the location of wiring and pipes.
f
Avoid touching the tip of a drill bit just after drilling, as
it may be hot
ASSAMBLY
Warning! Before assembly, make sure that the tool is
switched off and unplugged.
Fitting the side handle and depth stop (Fig. B)
Turn the grip counterclockwise until you can slide the
side handle (7) onto the front of the tool as shown.
f
Rotate the side handle into the desired position.
f
Insert the depth stop (6) into the mounting hole as
shown.
f
Set the drilling depth as described below.
f
Tighten the side handle by turning the grip clockwise.
Fitting a drill bit or screwdriver bit
Keyed chuck (Fig. C)
f
Open the chuck by turning the sleeve (9)
counterclockwise.
f
Insert the bit shaft (8) into the chuck.
f
Insert the chuck key (10) into each hole (11) in the side
of the chuck and turn clockwise until tight.
Removing and refitting the chuck (Fig. D)
f
Open the chuck as far as possible.
f
Remove the chuck retaining screw, located in the
chuck, by turning it clockwise using a screwdriver.
f
Tighten an Allen key into the chuck and strike it with
a hammer as shown.
f
Remove the Allen key.
f
Remove the chuck by turning it counterclockwise.
f
To refit the chuck, screw it onto the spindle and secure
it with the chuck retaining screw.
Read
Instructions
Manual
Use Eye
Protection
Use Ear
Protection
V ........ Volts
A ........ Amperes
Hz ....... Hertz
W ........ Watts
min ..... minutes
..... Alternating
Current
..... Direct
Current
n
0
....... No-Load
Speed
...... Class II
Construction
.... Earthing
Terminal
.... Safety Alert
Symbol
.../min.. Revolutions
or Recipro-
cation per
minute
qualified person, but not authorized by
BLACK+DECKER, the warranty will not be valid.
4
•
ENGLISH
4 • ENGLISH
making any adjustments, changing accessories,
or storing power tools. Such preventive safety measures
reduce the risk of starting the power tool accidentally.
d. Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the power
tool or these instructions to operate the power
tool. Power tools are dangerous in the hands
of untrained users.
e. Maintain power tools. Check for misalignment
or binding of moving parts, breakage of parts and
any other condition that may affect the power
tools operation. If damaged, have the power tool
repaired before use. Many accidents are caused by
poorly maintained power tools.
f. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
5. Service
a. Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
6. Electrical safety
Your tool is double insulated; therefore no earth
wire is required. Always check that the main voltage
corresponds to the voltage on the rating plate.
Warning! If the power cord is damaged, it must
be replaced by the manufacturer, authorized
BLACK+DECKER Service Center or an equally
qualified person in order to avoid damage or
injury. If the power cord is replaced by an equally
7. Labels on tool
The label on your tool may include the following symbols:
FEATURES (Fig. A)
1. Variable speed switch
2. Lock-on button
3. Forward/reverse slider
4. Drilling mode selector
5. Chuck
6. Depth stop
7. Side handle
ADDITIONAL SAFETY INSTRUCTIONS
FOR HAMMER DRILL
f
Wear ear protectors with impact drills. Exposure to
noise can cause hearing loss.
f
Use auxiliary handles supplied with the tool. Loss
of control can cause personal injury.
f
Hold power tool by insulated gripping surfaces
when performing an operation where the cutting
tool may contact hidden wiring or its own cord.
Contact with a “live” wire will also make exposed metal
parts of the power tool “live” and shock the operator.
f
Use clamps or another practical way to secure
and support the workpiece to a stable platform.
Holding the work by hand or against your body leaves
it unstable and may lead to loss of control.
f
Before drilling into walls, floors or ceilings check for
the location of wiring and pipes.
f
Avoid touching the tip of a drill bit just after drilling, as
it may be hot
ASSAMBLY
Warning! Before assembly, make sure that the tool is
switched off and unplugged.
Fitting the side handle and depth stop (Fig. B)
Turn the grip counterclockwise until you can slide the
side handle (7) onto the front of the tool as shown.
f
Rotate the side handle into the desired position.
f
Insert the depth stop (6) into the mounting hole as
shown.
f
Set the drilling depth as described below.
f
Tighten the side handle by turning the grip clockwise.
Fitting a drill bit or screwdriver bit
Keyed chuck (Fig. C)
f
Open the chuck by turning the sleeve (9)
counterclockwise.
f
Insert the bit shaft (8) into the chuck.
f
Insert the chuck key (10) into each hole (11) in the side
of the chuck and turn clockwise until tight.
Removing and refitting the chuck (Fig. D)
f
Open the chuck as far as possible.
f
Remove the chuck retaining screw, located in the
chuck, by turning it clockwise using a screwdriver.
f
Tighten an Allen key into the chuck and strike it with
a hammer as shown.
f
Remove the Allen key.
f
Remove the chuck by turning it counterclockwise.
f
To refit the chuck, screw it onto the spindle and secure
it with the chuck retaining screw.
Read
Instructions
Manual
Use Eye
Protection
Use Ear
Protection
V ........ Volts
A ........ Amperes
Hz ....... Hertz
W ........ Watts
min ..... minutes
..... Alternating
Current
..... Direct
Current
n
0
....... No-Load
Speed
...... Class II
Construction
.... Earthing
Terminal
.... Safety Alert
Symbol
.../min.. Revolutions
or Recipro-
cation per
minute
qualified person, but not authorized by
BLACK+DECKER, the warranty will not be valid.
4
•
ENGLISH
4 • ENGLISH
making any adjustments, changing accessories,
or storing power tools. Such preventive safety measures
reduce the risk of starting the power tool accidentally.
d. Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the power
tool or these instructions to operate the power
tool. Power tools are dangerous in the hands
of untrained users.
e. Maintain power tools. Check for misalignment
or binding of moving parts, breakage of parts and
any other condition that may affect the power
tools operation. If damaged, have the power tool
repaired before use. Many accidents are caused by
poorly maintained power tools.
f. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
5. Service
a. Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
6. Electrical safety
Your tool is double insulated; therefore no earth
wire is required. Always check that the main voltage
corresponds to the voltage on the rating plate.
Warning! If the power cord is damaged, it must
be replaced by the manufacturer, authorized
BLACK+DECKER Service Center or an equally
qualified person in order to avoid damage or
injury. If the power cord is replaced by an equally
7. Labels on tool
The label on your tool may include the following symbols:
FEATURES (Fig. A)
1. Variable speed switch
2. Lock-on button
3. Forward/reverse slider
4. Drilling mode selector
5. Chuck
6. Depth stop
7. Side handle
ADDITIONAL SAFETY INSTRUCTIONS
FOR HAMMER DRILL
f
Wear ear protectors with impact drills. Exposure to
noise can cause hearing loss.
f
Use auxiliary handles supplied with the tool. Loss
of control can cause personal injury.
f
Hold power tool by insulated gripping surfaces
when performing an operation where the cutting
tool may contact hidden wiring or its own cord.
Contact with a “live” wire will also make exposed metal
parts of the power tool “live” and shock the operator.
f
Use clamps or another practical way to secure
and support the workpiece to a stable platform.
Holding the work by hand or against your body leaves
it unstable and may lead to loss of control.
f
Before drilling into walls, floors or ceilings check for
the location of wiring and pipes.
f
Avoid touching the tip of a drill bit just after drilling, as
it may be hot
ASSAMBLY
Warning! Before assembly, make sure that the tool is
switched off and unplugged.
Fitting the side handle and depth stop (Fig. B)
Turn the grip counterclockwise until you can slide the
side handle (7) onto the front of the tool as shown.
f
Rotate the side handle into the desired position.
f
Insert the depth stop (6) into the mounting hole as
shown.
f
Set the drilling depth as described below.
f
Tighten the side handle by turning the grip clockwise.
Fitting a drill bit or screwdriver bit
Keyed chuck (Fig. C)
f
Open the chuck by turning the sleeve (9)
counterclockwise.
f
Insert the bit shaft (8) into the chuck.
f
Insert the chuck key (10) into each hole (11) in the side
of the chuck and turn clockwise until tight.
Removing and refitting the chuck (Fig. D)
f
Open the chuck as far as possible.
f
Remove the chuck retaining screw, located in the
chuck, by turning it clockwise using a screwdriver.
f
Tighten an Allen key into the chuck and strike it with
a hammer as shown.
f
Remove the Allen key.
f
Remove the chuck by turning it counterclockwise.
f
To refit the chuck, screw it onto the spindle and secure
it with the chuck retaining screw.
Read
Instructions
Manual
Use Eye
Protection
Use Ear
Protection
V ........ Volts
A ........ Amperes
Hz ....... Hertz
W ........ Watts
min ..... minutes
..... Alternating
Current
..... Direct
Current
n
0
....... No-Load
Speed
...... Class II
Construction
.... Earthing
Terminal
.... Safety Alert
Symbol
.../min.. Revolutions
or Recipro-
cation per
minute
qualified person, but not authorized by
BLACK+DECKER, the warranty will not be valid.
4
•
ENGLISH
4 • ENGLISH
making any adjustments, changing accessories,
or storing power tools. Such preventive safety measures
reduce the risk of starting the power tool accidentally.
d. Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the power
tool or these instructions to operate the power
tool. Power tools are dangerous in the hands
of untrained users.
e. Maintain power tools. Check for misalignment
or binding of moving parts, breakage of parts and
any other condition that may affect the power
tools operation. If damaged, have the power tool
repaired before use. Many accidents are caused by
poorly maintained power tools.
f. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
5. Service
a. Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
6. Electrical safety
Your tool is double insulated; therefore no earth
wire is required. Always check that the main voltage
corresponds to the voltage on the rating plate.
Warning! If the power cord is damaged, it must
be replaced by the manufacturer, authorized
BLACK+DECKER Service Center or an equally
qualified person in order to avoid damage or
injury. If the power cord is replaced by an equally
7. Labels on tool
The label on your tool may include the following symbols:
FEATURES (Fig. A)
1. Variable speed switch
2. Lock-on button
3. Forward/reverse slider
4. Drilling mode selector
5. Chuck
6. Depth stop
7. Side handle
ADDITIONAL SAFETY INSTRUCTIONS
FOR HAMMER DRILL
f
Wear ear protectors with impact drills. Exposure to
noise can cause hearing loss.
f
Use auxiliary handles supplied with the tool. Loss
of control can cause personal injury.
f
Hold power tool by insulated gripping surfaces
when performing an operation where the cutting
tool may contact hidden wiring or its own cord.
Contact with a “live” wire will also make exposed metal
parts of the power tool “live” and shock the operator.
f
Use clamps or another practical way to secure
and support the workpiece to a stable platform.
Holding the work by hand or against your body leaves
it unstable and may lead to loss of control.
f
Before drilling into walls, floors or ceilings check for
the location of wiring and pipes.
f
Avoid touching the tip of a drill bit just after drilling, as
it may be hot
ASSAMBLY
Warning! Before assembly, make sure that the tool is
switched off and unplugged.
Fitting the side handle and depth stop (Fig. B)
Turn the grip counterclockwise until you can slide the
side handle (7) onto the front of the tool as shown.
f
Rotate the side handle into the desired position.
f
Insert the depth stop (6) into the mounting hole as
shown.
f
Set the drilling depth as described below.
f
Tighten the side handle by turning the grip clockwise.
Fitting a drill bit or screwdriver bit
Keyed chuck (Fig. C)
f
Open the chuck by turning the sleeve (9)
counterclockwise.
f
Insert the bit shaft (8) into the chuck.
f
Insert the chuck key (10) into each hole (11) in the side
of the chuck and turn clockwise until tight.
Removing and refitting the chuck (Fig. D)
f
Open the chuck as far as possible.
f
Remove the chuck retaining screw, located in the
chuck, by turning it clockwise using a screwdriver.
f
Tighten an Allen key into the chuck and strike it with
a hammer as shown.
f
Remove the Allen key.
f
Remove the chuck by turning it counterclockwise.
f
To refit the chuck, screw it onto the spindle and secure
it with the chuck retaining screw.
Read
Instructions
Manual
Use Eye
Protection
Use Ear
Protection
V ........ Volts
A ........ Amperes
Hz ....... Hertz
W ........ Watts
min ..... minutes
..... Alternating
Current
..... Direct
Current
n
0
....... No-Load
Speed
...... Class II
Construction
.... Earthing
Terminal
.... Safety Alert
Symbol
.../min.. Revolutions
or Recipro-
cation per
minute
qualified person, but not authorized by
BLACK+DECKER, the warranty will not be valid.
4
•
ENGLISH
4 • ENGLISH
making any adjustments, changing accessories,
or storing power tools. Such preventive safety measures
reduce the risk of starting the power tool accidentally.
d. Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the power
tool or these instructions to operate the power
tool. Power tools are dangerous in the hands
of untrained users.
e. Maintain power tools. Check for misalignment
or binding of moving parts, breakage of parts and
any other condition that may affect the power
tools operation. If damaged, have the power tool
repaired before use. Many accidents are caused by
poorly maintained power tools.
f. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
5. Service
a. Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
6. Electrical safety
Your tool is double insulated; therefore no earth
wire is required. Always check that the main voltage
corresponds to the voltage on the rating plate.
Warning! If the power cord is damaged, it must
be replaced by the manufacturer, authorized
BLACK+DECKER Service Center or an equally
qualified person in order to avoid damage or
injury. If the power cord is replaced by an equally
7. Labels on tool
The label on your tool may include the following symbols:
FEATURES (Fig. A)
1. Variable speed switch
2. Lock-on button
3. Forward/reverse slider
4. Drilling mode selector
5. Chuck
6. Depth stop
7. Side handle
ADDITIONAL SAFETY INSTRUCTIONS
FOR HAMMER DRILL
f
Wear ear protectors with impact drills. Exposure to
noise can cause hearing loss.
f
Use auxiliary handles supplied with the tool. Loss
of control can cause personal injury.
f
Hold power tool by insulated gripping surfaces
when performing an operation where the cutting
tool may contact hidden wiring or its own cord.
Contact with a “live” wire will also make exposed metal
parts of the power tool “live” and shock the operator.
f
Use clamps or another practical way to secure
and support the workpiece to a stable platform.
Holding the work by hand or against your body leaves
it unstable and may lead to loss of control.
f
Before drilling into walls, floors or ceilings check for
the location of wiring and pipes.
f
Avoid touching the tip of a drill bit just after drilling, as
it may be hot
ASSAMBLY
Warning! Before assembly, make sure that the tool is
switched off and unplugged.
Fitting the side handle and depth stop (Fig. B)
Turn the grip counterclockwise until you can slide the
side handle (7) onto the front of the tool as shown.
f
Rotate the side handle into the desired position.
f
Insert the depth stop (6) into the mounting hole as
shown.
f
Set the drilling depth as described below.
f
Tighten the side handle by turning the grip clockwise.
Fitting a drill bit or screwdriver bit
Keyed chuck (Fig. C)
f
Open the chuck by turning the sleeve (9)
counterclockwise.
f
Insert the bit shaft (8) into the chuck.
f
Insert the chuck key (10) into each hole (11) in the side
of the chuck and turn clockwise until tight.
Removing and refitting the chuck (Fig. D)
f
Open the chuck as far as possible.
f
Remove the chuck retaining screw, located in the
chuck, by turning it clockwise using a screwdriver.
f
Tighten an Allen key into the chuck and strike it with
a hammer as shown.
f
Remove the Allen key.
f
Remove the chuck by turning it counterclockwise.
f
To refit the chuck, screw it onto the spindle and secure
it with the chuck retaining screw.
Read
Instructions
Manual
Use Eye
Protection
Use Ear
Protection
V ........ Volts
A ........ Amperes
Hz ....... Hertz
W ........ Watts
min ..... minutes
..... Alternating
Current
..... Direct
Current
n
0
....... No-Load
Speed
...... Class II
Construction
.... Earthing
Terminal
.... Safety Alert
Symbol
.../min.. Revolutions
or Recipro-
cation per
minute
qualified person, but not authorized by
BLACK+DECKER, the warranty will not be valid.