Black & Decker HD555, Инструкция по эксплуатации

Страница: 5 / 12

ENGLISH ● 5

Set the drilling depth as described below.

Tighten the side handle by turning the grip clockwise.
Fitting a drill bit or screwdriver bit Keyed
chuck (Fig. C)

Open the chuck by turning the sleeve (9) counterclockwise.

Insert the bit shaft (8) into the chuck.

Insert the chuck key (10) into each hole (11) in the side
of the chuck and turn clockwise until tight.
Removing and refitting the chuck (Fig. D)

Open the chuck as far as possible.

Remove the chuck retaining screw, located in the
chuck, by turning it clockwise using a screwdriver.

Tighten an Allen key into the chuck and strike it with a
hammer as shown.

Remove the Allen key.

Remove the chuck by turning it counterclockwise.

To refit the chuck, screw it onto the spindle and secure
it with the chuck retaining screw.
USE
Warning! Let the tool work at its own pace. Do not overload.
Warning! Before drilling into walls, floors or ceilings,
check for the location of wiring and pipes.
Selecting the direction of rotation (Fig. E)
For drilling and for tightening screws, use forward (clockwise)
rotation. For loosening screws or removing a jammed drill bit,
use reverse (counterclockwise) rotation.

To select forward rotation, push the forward/reverse
slider (3) to the centre position.

To select reverse rotation, push the forward/reverse
slider to the left.
Warning! Never change the direction of rotation while the
motor is running.
Selecting the drilling mode

For drilling in masonry, set the drilling mode selector (3)
to the
ENGLISH
•
5
ENGLISH • 5
USE
Warning! Let the tool work at its own pace. Do not
overload.
Warning! Before drilling into walls, floors or ceilings,
check for the location of wiring and pipes.
Selecting the direction of rotation (Fig. E)
For drilling and for tightening screws, use forward
(clockwise) rotation. For loosening screws or removing a
jammed drill bit, use reverse (counterclockwise) rotation.
f
To select forward rotation, push the forward/reverse
slider (3) to the centre position.
f
To select reverse rotation, push the forward/reverse
slider to the left.
Warning! Never change the direction of rotation while
the motor is running.
Selecting the drilling mode
f
For drilling in masonry, set the drilling mode selector
(3) to the position.
f
For drilling in other materials and for screwdriving, set
the drilling mode selector to the position.
Setting the drilling depth (Fig. F)
f
Slacken the side handle (7) by turning the grip
counterclockwise.
f
Set the depth stop (6) to the desired position. The
maximum drilling depth is equal to the distance
between the tip of the drill bit and the front end of the
depth stop.
f
Tighten the side handle by turning the grip clockwise.
Switching on and off
f
To switch the tool on, press the speed switch (1).
For tools with variable speed switch, the tool speed
depends on how far you press the switch. As a
general rule, use low speeds for large diameter
drill bits and high speeds for smaller diameter drill bits.
f
For continuous operation, press the lock-on button (2)
and release the speed switch. This option is available
only at full speed. This option does not work in reverse
rotation. Reverse rotation available only for HD500.
f
To switch the tool off, release the speed switch.
To switch the tool off when in continuous operation,
press the speed switch once more and release it.
MAINTENANCE
Keep guards, air vents and the motor housing as clear as
possible of dust and dirt. Wipe with a clean cloth and blow
through with a low-pressure air supply. Excessive build-up
of metal dust can cause tracking of electrical current from
the internal parts to exposed metal parts.
Important! To assure product SAFETY and RELIABILITY,
repairs, maintenance and adjustment (other than those
listed in this manual) should be performed by authorized
service centers or other qualified service personnel,
always using identical replacement parts.
ACCESSORIES
Recommended accessories for use with your product
are available from your local dealer or authorized service
center.
PROTECTING THE ENVIRONMENT
Separate collection. This product must not be
disposed of with normal household waste.
Should you find one day that your
BLACK+DECKER product needs replacement, or
if it is of no further use to you, do not dispose of it
with household waste. Make this product available
for separate collection.
Separate collection of used products and packaging
allows materials to be recycled and used again.
Re-use of recycled materials helps prevent
environmental pollution and reduces the demand
for raw materials. Local regulations may provide for
separate collection of electrical products from the
household, at municipal waste sites or by the
retailer when you purchase a new product.
SERVICE INFORMATION
BLACK+DECKER offers a full network of company-owned
and authorized service locations throughtout Asia. All
BLACK+DECKER Service Centers are staffed with trained
personnel to provide customers with efficient and reliable
product service.
Whether you need technical advice, repair, or genuine
factory replacement parts, contact the BLACK+DECKER
location nearest to you.
NOTE
f
BLACK+DECKER’s policy is one of continuous
improvement to our products and, as such, we reserve
the right to change product specifications without prior
notice.
f
Standard equipment and accessories may vary by
country.
f
Product specifications may differ by country.
f
Complete product range may not be available in all
countries. Contact your local BLACK+DECKER
dealers for range availability.
position.

For drilling in other materials and for screwdriving, set
the drilling mode selector to the
ENGLISH
•
5
ENGLISH • 5
USE
Warning! Let the tool work at its own pace. Do not
overload.
Warning! Before drilling into walls, floors or ceilings,
check for the location of wiring and pipes.
Selecting the direction of rotation (Fig. E)
For drilling and for tightening screws, use forward
(clockwise) rotation. For loosening screws or removing a
jammed drill bit, use reverse (counterclockwise) rotation.
f
To select forward rotation, push the forward/reverse
slider (3) to the centre position.
f
To select reverse rotation, push the forward/reverse
slider to the left.
Warning! Never change the direction of rotation while
the motor is running.
Selecting the drilling mode
f
For drilling in masonry, set the drilling mode selector
(3) to the position.
f
For drilling in other materials and for screwdriving, set
the drilling mode selector to the position.
Setting the drilling depth (Fig. F)
f
Slacken the side handle (7) by turning the grip
counterclockwise.
f
Set the depth stop (6) to the desired position. The
maximum drilling depth is equal to the distance
between the tip of the drill bit and the front end of the
depth stop.
f
Tighten the side handle by turning the grip clockwise.
Switching on and off
f
To switch the tool on, press the speed switch (1).
For tools with variable speed switch, the tool speed
depends on how far you press the switch. As a
general rule, use low speeds for large diameter
drill bits and high speeds for smaller diameter drill bits.
f
For continuous operation, press the lock-on button (2)
and release the speed switch. This option is available
only at full speed. This option does not work in reverse
rotation. Reverse rotation available only for HD500.
f
To switch the tool off, release the speed switch.
To switch the tool off when in continuous operation,
press the speed switch once more and release it.
MAINTENANCE
Keep guards, air vents and the motor housing as clear as
possible of dust and dirt. Wipe with a clean cloth and blow
through with a low-pressure air supply. Excessive build-up
of metal dust can cause tracking of electrical current from
the internal parts to exposed metal parts.
Important! To assure product SAFETY and RELIABILITY,
repairs, maintenance and adjustment (other than those
listed in this manual) should be performed by authorized
service centers or other qualified service personnel,
always using identical replacement parts.
ACCESSORIES
Recommended accessories for use with your product
are available from your local dealer or authorized service
center.
PROTECTING THE ENVIRONMENT
Separate collection. This product must not be
disposed of with normal household waste.
Should you find one day that your
BLACK+DECKER product needs replacement, or
if it is of no further use to you, do not dispose of it
with household waste. Make this product available
for separate collection.
Separate collection of used products and packaging
allows materials to be recycled and used again.
Re-use of recycled materials helps prevent
environmental pollution and reduces the demand
for raw materials. Local regulations may provide for
separate collection of electrical products from the
household, at municipal waste sites or by the
retailer when you purchase a new product.
SERVICE INFORMATION
BLACK+DECKER offers a full network of company-owned
and authorized service locations throughtout Asia. All
BLACK+DECKER Service Centers are staffed with trained
personnel to provide customers with efficient and reliable
product service.
Whether you need technical advice, repair, or genuine
factory replacement parts, contact the BLACK+DECKER
location nearest to you.
NOTE
f
BLACK+DECKER’s policy is one of continuous
improvement to our products and, as such, we reserve
the right to change product specifications without prior
notice.
f
Standard equipment and accessories may vary by
country.
f
Product specifications may differ by country.
f
Complete product range may not be available in all
countries. Contact your local BLACK+DECKER
dealers for range availability.
position.
Setting the drilling depth (Fig. F)

Slacken the side handle (7) by turning the grip counter-
clockwise.

Set the depth stop (6) to the desired position. The maxi-
mum drilling depth is equal to the distance between the tip
ENGLISH
•
5 ENGLISH • 5
USE
Warning! Let the tool work at its own pace. Do not
overload.
Warning! Before drilling into walls, floors or ceilings,
check for the location of wiring and pipes.
Selecting the direction of rotation (Fig. E)
For drilling and for tightening screws, use forward
(clockwise) rotation. For loosening screws or removing a
jammed drill bit, use reverse (counterclockwise) rotation.
f
To select forward rotation, push the forward/reverse
slider (3) to the centre position.
f
To select reverse rotation, push the forward/reverse
slider to the left.
Warning! Never change the direction of rotation while
the motor is running.
Selecting the drilling mode
f
For drilling in masonry, set the drilling mode selector
(3) to the position.
f
For drilling in other materials and for screwdriving, set
the drilling mode selector to the position.
Setting the drilling depth (Fig. F)
f
Slacken the side handle (7) by turning the grip
counterclockwise.
f
Set the depth stop (6) to the desired position. The
maximum drilling depth is equal to the distance
between the tip of the drill bit and the front end of the
depth stop.
f
Tighten the side handle by turning the grip clockwise.
Switching on and off
f
To switch the tool on, press the speed switch (1).
For tools with variable speed switch, the tool speed
depends on how far you press the switch. As a
general rule, use low speeds for large diameter
drill bits and high speeds for smaller diameter drill bits.
f
For continuous operation, press the lock-on button (2)
and release the speed switch. This option is available
only at full speed. This option does not work in reverse
rotation. Reverse rotation available only for HD500.
f
To switch the tool off, release the speed switch.
To switch the tool off when in continuous operation,
press the speed switch once more and release it.
MAINTENANCE
Keep guards, air vents and the motor housing as clear as
possible of dust and dirt. Wipe with a clean cloth and blow
through with a low-pressure air supply. Excessive build-up
of metal dust can cause tracking of electrical current from
the internal parts to exposed metal parts.
Important! To assure product SAFETY and RELIABILITY,
repairs, maintenance and adjustment (other than those
listed in this manual) should be performed by authorized
service centers or other qualified service personnel,
always using identical replacement parts.
ACCESSORIES
Recommended accessories for use with your product
are available from your local dealer or authorized service
center.
PROTECTING THE ENVIRONMENT
Separate collection. This product must not be
disposed of with normal household waste.
Should you find one day that your
BLACK+DECKER product needs replacement, or
if it is of no further use to you, do not dispose of it
with household waste. Make this product available
for separate collection.
Separate collection of used products and packaging
allows materials to be recycled and used again.
Re-use of recycled materials helps prevent
environmental pollution and reduces the demand
for raw materials. Local regulations may provide for
separate collection of electrical products from the
household, at municipal waste sites or by the
retailer when you purchase a new product.
SERVICE INFORMATION
BLACK+DECKER offers a full network of company-owned
and authorized service locations throughtout Asia. All
BLACK+DECKER Service Centers are staffed with trained
personnel to provide customers with efficient and reliable
product service.
Whether you need technical advice, repair, or genuine
factory replacement parts, contact the BLACK+DECKER
location nearest to you.
NOTE
f
BLACK+DECKER’s policy is one of continuous
improvement to our products and, as such, we reserve
the right to change product specifications without prior
notice.
f
Standard equipment and accessories may vary by
country.
f
Product specifications may differ by country.
f
Complete product range may not be available in all
countries. Contact your local BLACK+DECKER
dealers for range availability.
ENGLISH
•
5
ENGLISH • 5
USE
Warning! Let the tool work at its own pace. Do not
overload.
Warning! Before drilling into walls, floors or ceilings,
check for the location of wiring and pipes.
Selecting the direction of rotation (Fig. E)
For drilling and for tightening screws, use forward
(clockwise) rotation. For loosening screws or removing a
jammed drill bit, use reverse (counterclockwise) rotation.
f
To select forward rotation, push the forward/reverse
slider (3) to the centre position.
f
To select reverse rotation, push the forward/reverse
slider to the left.
Warning! Never change the direction of rotation while
the motor is running.
Selecting the drilling mode
f
For drilling in masonry, set the drilling mode selector
(3) to the position.
f
For drilling in other materials and for screwdriving, set
the drilling mode selector to the position.
Setting the drilling depth (Fig. F)
f
Slacken the side handle (7) by turning the grip
counterclockwise.
f
Set the depth stop (6) to the desired position. The
maximum drilling depth is equal to the distance
between the tip of the drill bit and the front end of the
depth stop.
f
Tighten the side handle by turning the grip clockwise.
Switching on and off
f
To switch the tool on, press the speed switch (1).
For tools with variable speed switch, the tool speed
depends on how far you press the switch. As a
general rule, use low speeds for large diameter
drill bits and high speeds for smaller diameter drill bits.
f
For continuous operation, press the lock-on button (2)
and release the speed switch. This option is available
only at full speed. This option does not work in reverse
rotation. Reverse rotation available only for HD500.
f
To switch the tool off, release the speed switch.
To switch the tool off when in continuous operation,
press the speed switch once more and release it.
MAINTENANCE
Keep guards, air vents and the motor housing as clear as
possible of dust and dirt. Wipe with a clean cloth and blow
through with a low-pressure air supply. Excessive build-up
of metal dust can cause tracking of electrical current from
the internal parts to exposed metal parts.
Important! To assure product SAFETY and RELIABILITY,
repairs, maintenance and adjustment (other than those
listed in this manual) should be performed by authorized
service centers or other qualified service personnel,
always using identical replacement parts.
ACCESSORIES
Recommended accessories for use with your product
are available from your local dealer or authorized service
center.
PROTECTING THE ENVIRONMENT
Separate collection. This product must not be
disposed of with normal household waste.
Should you find one day that your
BLACK+DECKER product needs replacement, or
if it is of no further use to you, do not dispose of it
with household waste. Make this product available
for separate collection.
Separate collection of used products and packaging
allows materials to be recycled and used again.
Re-use of recycled materials helps prevent
environmental pollution and reduces the demand
for raw materials. Local regulations may provide for
separate collection of electrical products from the
household, at municipal waste sites or by the
retailer when you purchase a new product.
SERVICE INFORMATION
BLACK+DECKER offers a full network of company-owned
and authorized service locations throughtout Asia. All
BLACK+DECKER Service Centers are staffed with trained
personnel to provide customers with efficient and reliable
product service.
Whether you need technical advice, repair, or genuine
factory replacement parts, contact the BLACK+DECKER
location nearest to you.
NOTE
f
BLACK+DECKER’s policy is one of continuous
improvement to our products and, as such, we reserve
the right to change product specifications without prior
notice.
f
Standard equipment and accessories may vary by
country.
f
Product specifications may differ by country.
f
Complete product range may not be available in all
countries. Contact your local BLACK+DECKER
dealers for range availability.
ENGLISH
•
5 ENGLISH • 5
USE
Warning! Let the tool work at its own pace. Do not
overload.
Warning! Before drilling into walls, floors or ceilings,
check for the location of wiring and pipes.
Selecting the direction of rotation (Fig. E)
For drilling and for tightening screws, use forward
(clockwise) rotation. For loosening screws or removing a
jammed drill bit, use reverse (counterclockwise) rotation.
f
To select forward rotation, push the forward/reverse
slider (3) to the centre position.
f
To select reverse rotation, push the forward/reverse
slider to the left.
Warning! Never change the direction of rotation while
the motor is running.
Selecting the drilling mode
f
For drilling in masonry, set the drilling mode selector
(3) to the position.
f
For drilling in other materials and for screwdriving, set
the drilling mode selector to the position.
Setting the drilling depth (Fig. F)
f
Slacken the side handle (7) by turning the grip
counterclockwise.
f
Set the depth stop (6) to the desired position. The
maximum drilling depth is equal to the distance
between the tip of the drill bit and the front end of the
depth stop.
f
Tighten the side handle by turning the grip clockwise.
Switching on and off
f
To switch the tool on, press the speed switch (1).
For tools with variable speed switch, the tool speed
depends on how far you press the switch. As a
general rule, use low speeds for large diameter
drill bits and high speeds for smaller diameter drill bits.
f
For continuous operation, press the lock-on button (2)
and release the speed switch. This option is available
only at full speed. This option does not work in reverse
rotation. Reverse rotation available only for HD500.
f
To switch the tool off, release the speed switch.
To switch the tool off when in continuous operation,
press the speed switch once more and release it.
MAINTENANCE
Keep guards, air vents and the motor housing as clear as
possible of dust and dirt. Wipe with a clean cloth and blow
through with a low-pressure air supply. Excessive build-up
of metal dust can cause tracking of electrical current from
the internal parts to exposed metal parts.
Important! To assure product SAFETY and RELIABILITY,
repairs, maintenance and adjustment (other than those
listed in this manual) should be performed by authorized
service centers or other qualified service personnel,
always using identical replacement parts.
ACCESSORIES
Recommended accessories for use with your product
are available from your local dealer or authorized service
center.
PROTECTING THE ENVIRONMENT
Separate collection. This product must not be
disposed of with normal household waste.
Should you find one day that your
BLACK+DECKER product needs replacement, or
if it is of no further use to you, do not dispose of it
with household waste. Make this product available
for separate collection.
Separate collection of used products and packaging
allows materials to be recycled and used again.
Re-use of recycled materials helps prevent
environmental pollution and reduces the demand
for raw materials. Local regulations may provide for
separate collection of electrical products from the
household, at municipal waste sites or by the
retailer when you purchase a new product.
SERVICE INFORMATION
BLACK+DECKER offers a full network of company-owned
and authorized service locations throughtout Asia. All
BLACK+DECKER Service Centers are staffed with trained
personnel to provide customers with efficient and reliable
product service.
Whether you need technical advice, repair, or genuine
factory replacement parts, contact the BLACK+DECKER
location nearest to you.
NOTE
f
BLACK+DECKER’s policy is one of continuous
improvement to our products and, as such, we reserve
the right to change product specifications without prior
notice.
f
Standard equipment and accessories may vary by
country.
f
Product specifications may differ by country.
f
Complete product range may not be available in all
countries. Contact your local BLACK+DECKER
dealers for range availability.
of the drill bit and the front end of the depth stop.

Tighten the side handle by turning the grip clockwise.
Switching on and off

To switch the tool on, press the speed switch (1).
For tools with variable speed switch, the tool speed
depends on how far you press the switch. As a general
rule, use low speeds for large diameter drill bits and
high speeds for smaller diameter drill bits.

For continuous operation, press the lock-on button (2)
and release the speed switch. This option is available
only at full speed.

To switch the tool off, release the speed switch. To
switch the tool off when in continuous operation, press
the speed switch once more and release it.
MAINTENANCE
Keep guards, air vents and the motor housing as clear as
possible of dust and dirt. Wipe with a clean cloth and blow
through with a low-pressure air supply. Excessive build-up of
metal dust can cause tracking of electrical current from the
internal parts to exposed metal parts.
Important! To assure product SAFETY and RELIABILITY,
repairs, maintenance and adjustment (other than those listed
in this manual) should be performed by authorized service
centers or other qualified service personnel, always using
identical replacement parts.
ACCESSORIES
Recommended accessories for use with your product are
available from your local dealer or authorized service center.
PROTECTING THE ENVIRONMENT
Separate collection. This product must not be dis-
posed of with normal household waste. Should you
find one day that your BLACK+DECKER product
needs replacement, or if it is of no further use to
you, do not dispose of it with household waste.
Make this product available for separate collection.
Separate collection of used products and packaging
allows materials to be recycled and used again.
Re-use of recycled materials helps prevent
environmental pollution and reduces the demand
for raw materials. Local regulations may provide
for separate collection of electrical products from
the household, at municipal waste sites or by the
retailer when you purchase a new product.
ENGLISH
•
5 ENGLISH • 5
USE
Warning! Let the tool work at its own pace. Do not
overload.
Warning! Before drilling into walls, floors or ceilings,
check for the location of wiring and pipes.
Selecting the direction of rotation (Fig. E)
For drilling and for tightening screws, use forward
(clockwise) rotation. For loosening screws or removing a
jammed drill bit, use reverse (counterclockwise) rotation.
f
To select forward rotation, push the forward/reverse
slider (3) to the centre position.
f
To select reverse rotation, push the forward/reverse
slider to the left.
Warning! Never change the direction of rotation while
the motor is running.
Selecting the drilling mode
f
For drilling in masonry, set the drilling mode selector
(3) to the position.
f
For drilling in other materials and for screwdriving, set
the drilling mode selector to the position.
Setting the drilling depth (Fig. F)
f
Slacken the side handle (7) by turning the grip
counterclockwise.
f
Set the depth stop (6) to the desired position. The
maximum drilling depth is equal to the distance
between the tip of the drill bit and the front end of the
depth stop.
f
Tighten the side handle by turning the grip clockwise.
Switching on and off
f
To switch the tool on, press the speed switch (1).
For tools with variable speed switch, the tool speed
depends on how far you press the switch. As a
general rule, use low speeds for large diameter
drill bits and high speeds for smaller diameter drill bits.
f
For continuous operation, press the lock-on button (2)
and release the speed switch. This option is available
only at full speed. This option does not work in reverse
rotation. Reverse rotation available only for HD500.
f
To switch the tool off, release the speed switch.
To switch the tool off when in continuous operation,
press the speed switch once more and release it.
MAINTENANCE
Keep guards, air vents and the motor housing as clear as
possible of dust and dirt. Wipe with a clean cloth and blow
through with a low-pressure air supply. Excessive build-up
of metal dust can cause tracking of electrical current from
the internal parts to exposed metal parts.
Important! To assure product SAFETY and RELIABILITY,
repairs, maintenance and adjustment (other than those
listed in this manual) should be performed by authorized
service centers or other qualified service personnel,
always using identical replacement parts.
ACCESSORIES
Recommended accessories for use with your product
are available from your local dealer or authorized service
center.
PROTECTING THE ENVIRONMENT
Separate collection. This product must not be
disposed of with normal household waste.
Should you find one day that your
BLACK+DECKER product needs replacement, or
if it is of no further use to you, do not dispose of it
with household waste. Make this product available
for separate collection.
Separate collection of used products and packaging
allows materials to be recycled and used again.
Re-use of recycled materials helps prevent
environmental pollution and reduces the demand
for raw materials. Local regulations may provide for
separate collection of electrical products from the
household, at municipal waste sites or by the
retailer when you purchase a new product.
SERVICE INFORMATION
BLACK+DECKER offers a full network of company-owned
and authorized service locations throughtout Asia. All
BLACK+DECKER Service Centers are staffed with trained
personnel to provide customers with efficient and reliable
product service.
Whether you need technical advice, repair, or genuine
factory replacement parts, contact the BLACK+DECKER
location nearest to you.
NOTE
f
BLACK+DECKER’s policy is one of continuous
improvement to our products and, as such, we reserve
the right to change product specifications without prior
notice.
f
Standard equipment and accessories may vary by
country.
f
Product specifications may differ by country.
f
Complete product range may not be available in all
countries. Contact your local BLACK+DECKER
dealers for range availability.
ENGLISH
•
5
ENGLISH • 5
USE
Warning! Let the tool work at its own pace. Do not
overload.
Warning! Before drilling into walls, floors or ceilings,
check for the location of wiring and pipes.
Selecting the direction of rotation (Fig. E)
For drilling and for tightening screws, use forward
(clockwise) rotation. For loosening screws or removing a
jammed drill bit, use reverse (counterclockwise) rotation.
f
To select forward rotation, push the forward/reverse
slider (3) to the centre position.
f
To select reverse rotation, push the forward/reverse
slider to the left.
Warning! Never change the direction of rotation while
the motor is running.
Selecting the drilling mode
f
For drilling in masonry, set the drilling mode selector
(3) to the position.
f
For drilling in other materials and for screwdriving, set
the drilling mode selector to the position.
Setting the drilling depth (Fig. F)
f
Slacken the side handle (7) by turning the grip
counterclockwise.
f
Set the depth stop (6) to the desired position. The
maximum drilling depth is equal to the distance
between the tip of the drill bit and the front end of the
depth stop.
f
Tighten the side handle by turning the grip clockwise.
Switching on and off
f
To switch the tool on, press the speed switch (1).
For tools with variable speed switch, the tool speed
depends on how far you press the switch. As a
general rule, use low speeds for large diameter
drill bits and high speeds for smaller diameter drill bits.
f
For continuous operation, press the lock-on button (2)
and release the speed switch. This option is available
only at full speed. This option does not work in reverse
rotation. Reverse rotation available only for HD500.
f
To switch the tool off, release the speed switch.
To switch the tool off when in continuous operation,
press the speed switch once more and release it.
MAINTENANCE
Keep guards, air vents and the motor housing as clear as
possible of dust and dirt. Wipe with a clean cloth and blow
through with a low-pressure air supply. Excessive build-up
of metal dust can cause tracking of electrical current from
the internal parts to exposed metal parts.
Important! To assure product SAFETY and RELIABILITY,
repairs, maintenance and adjustment (other than those
listed in this manual) should be performed by authorized
service centers or other qualified service personnel,
always using identical replacement parts.
ACCESSORIES
Recommended accessories for use with your product
are available from your local dealer or authorized service
center.
PROTECTING THE ENVIRONMENT
Separate collection. This product must not be
disposed of with normal household waste.
Should you find one day that your
BLACK+DECKER product needs replacement, or
if it is of no further use to you, do not dispose of it
with household waste. Make this product available
for separate collection.
Separate collection of used products and packaging
allows materials to be recycled and used again.
Re-use of recycled materials helps prevent
environmental pollution and reduces the demand
for raw materials. Local regulations may provide for
separate collection of electrical products from the
household, at municipal waste sites or by the
retailer when you purchase a new product.
SERVICE INFORMATION
BLACK+DECKER offers a full network of company-owned
and authorized service locations throughtout Asia. All
BLACK+DECKER Service Centers are staffed with trained
personnel to provide customers with efficient and reliable
product service.
Whether you need technical advice, repair, or genuine
factory replacement parts, contact the BLACK+DECKER
location nearest to you.
NOTE
f
BLACK+DECKER’s policy is one of continuous
improvement to our products and, as such, we reserve
the right to change product specifications without prior
notice.
f
Standard equipment and accessories may vary by
country.
f
Product specifications may differ by country.
f
Complete product range may not be available in all
countries. Contact your local BLACK+DECKER
dealers for range availability.
ENGLISH
•
5
ENGLISH • 5
USE
Warning! Let the tool work at its own pace. Do not
overload.
Warning! Before drilling into walls, floors or ceilings,
check for the location of wiring and pipes.
Selecting the direction of rotation (Fig. E)
For drilling and for tightening screws, use forward
(clockwise) rotation. For loosening screws or removing a
jammed drill bit, use reverse (counterclockwise) rotation.
f
To select forward rotation, push the forward/reverse
slider (3) to the centre position.
f
To select reverse rotation, push the forward/reverse
slider to the left.
Warning! Never change the direction of rotation while
the motor is running.
Selecting the drilling mode
f
For drilling in masonry, set the drilling mode selector
(3) to the position.
f
For drilling in other materials and for screwdriving, set
the drilling mode selector to the position.
Setting the drilling depth (Fig. F)
f
Slacken the side handle (7) by turning the grip
counterclockwise.
f
Set the depth stop (6) to the desired position. The
maximum drilling depth is equal to the distance
between the tip of the drill bit and the front end of the
depth stop.
f
Tighten the side handle by turning the grip clockwise.
Switching on and off
f
To switch the tool on, press the speed switch (1).
For tools with variable speed switch, the tool speed
depends on how far you press the switch. As a
general rule, use low speeds for large diameter
drill bits and high speeds for smaller diameter drill bits.
f
For continuous operation, press the lock-on button (2)
and release the speed switch. This option is available
only at full speed. This option does not work in reverse
rotation. Reverse rotation available only for HD500.
f
To switch the tool off, release the speed switch.
To switch the tool off when in continuous operation,
press the speed switch once more and release it.
MAINTENANCE
Keep guards, air vents and the motor housing as clear as
possible of dust and dirt. Wipe with a clean cloth and blow
through with a low-pressure air supply. Excessive build-up
of metal dust can cause tracking of electrical current from
the internal parts to exposed metal parts.
Important! To assure product SAFETY and RELIABILITY,
repairs, maintenance and adjustment (other than those
listed in this manual) should be performed by authorized
service centers or other qualified service personnel,
always using identical replacement parts.
ACCESSORIES
Recommended accessories for use with your product
are available from your local dealer or authorized service
center.
PROTECTING THE ENVIRONMENT
Separate collection. This product must not be
disposed of with normal household waste.
Should you find one day that your
BLACK+DECKER product needs replacement, or
if it is of no further use to you, do not dispose of it
with household waste. Make this product available
for separate collection.
Separate collection of used products and packaging
allows materials to be recycled and used again.
Re-use of recycled materials helps prevent
environmental pollution and reduces the demand
for raw materials. Local regulations may provide for
separate collection of electrical products from the
household, at municipal waste sites or by the
retailer when you purchase a new product.
SERVICE INFORMATION
BLACK+DECKER offers a full network of company-owned
and authorized service locations throughtout Asia. All
BLACK+DECKER Service Centers are staffed with trained
personnel to provide customers with efficient and reliable
product service.
Whether you need technical advice, repair, or genuine
factory replacement parts, contact the BLACK+DECKER
location nearest to you.
NOTE
f
BLACK+DECKER’s policy is one of continuous
improvement to our products and, as such, we reserve
the right to change product specifications without prior
notice.
f
Standard equipment and accessories may vary by
country.
f
Product specifications may differ by country.
f
Complete product range may not be available in all
countries. Contact your local BLACK+DECKER
dealers for range availability.