BK Radio DMH 5992 Скачать руководство пользователя страница 27

Страница: 27 / 34

RELM/BK Radio

OTHER OPERATIONAL FEATURES

The BK Radio G Series radio is based on a microprocessor core that

allows extra features and operational characteristics to be programmed

into the radio. Your dealer can help define the best operational settings

for your system and program them into the radio.

SCAN DELAY

Scan delay lets the radio receive a response to a transmission before

scanning the other channels for activity. If you find that your scanner is

restarting before message replies are received, you can ask your dealer

to increase the scan delay time (0-7.5 seconds).

This timer is also used to allow for Talkback Scan.

HI/LO POWER

Each channel in the radio can be individually programmed to always

transmit in low-power mode, regardless of the radio’s

[LPW]

button

(or microphone keypad

[FCN]

menu setting). If the programming for

the channel allows high-power transmissions, the power level can be

selected with the

[LPW]

button or the keypad

[FCN]

menu.

DTMF ENCODING (Analog Mode Only)

Radios with keypad-equipped microphones can be programmed to

enable DTMF (Dual Tone Multiple Frequency) encoding. To send DTMF

tones (similar to the tones used by a standard push-button telephone):

Press and hold the PTT switch.

Press any of the keys on the microphone’s keypad.

You will hear a sidetone.

The FCN, PRI, ENT, and CLR keys respond as DTMF tones A, B, C, and

D, respectively.

ANI ENCODING (Analog Mode Only)

ANI encoding (Automatic Number Identification), if enabled, transmits a

sequence of DTMF tones each time you press the

PTT

switch. You will

hear a sidetone. Your dealer can program the ANI number to be sent.

Содержание DMH 5992



































Результаты поиска

Содержание DMH 5992

Отзывы:

Похожие инструкции для DMH 5992

Бренды по названию

Популярные бренды

BK Radio DMH 5992, Руководство пользователя

Результаты поиска

Содержание DMH 5992

Отзывы:

Похожие инструкции для DMH 5992

Бренды по названию

Популярные бренды