BK Radio DMH 5992 Скачать руководство пользователя страница 3

Страница: 3 / 34

RELM/BK Radio

INTRODUCTION

This section contains information concerning the operational procedures

for BK Radio DMH APCO Project 25 digital mobile radios. To meet

backwards compatibility as defined by the APCO Project 25 standard, the

DMH digital mobile radio provides users the ability to interoperate with

narrow or wide band analog channels as well as digital systems. Please

take a moment to read the information in this manual so you can get

optimum performance from your new radio.

FCC REQUIREMENTS

Your radio must be properly licensed by the Federal Communications

Commission prior to use. Your BK Radio dealer can assist you in meeting

these requirements. Your dealer will program each radio with your

authorized frequencies, signaling codes, etc., and will be there to meet

your communications needs as your system expands.

SAFETY PRECAUTIONS

Do not operate the transmitter in close proximity

•

to blasting caps.

Do not operate the radio in an explosive atmo-

•

sphere (petroleum fuels, solvents, dust, etc.).

Do not operate the transmitter if a person out-

•

side the vehicle is less than three feet from the

antenna or touching the antenna.

Содержание DMH 5992



































Результаты поиска

Содержание DMH 5992

Отзывы:

Похожие инструкции для DMH 5992

Бренды по названию

Популярные бренды

BK Radio DMH 5992, Руководство пользователя

Результаты поиска

Содержание DMH 5992

Отзывы:

Похожие инструкции для DMH 5992

Бренды по названию

Популярные бренды