BIXOLON SPP-R200II Скачать руководство пользователя страница 137

Страница: 137 / 147

SPP-R200II Command Manual

Rev. 1.00

BIXOLON

- 137 -

BS L L

Function:

Select label mode

Code:

ASCII

Hex

Decimal

Range:

None

Default:

None

Description:

■

This commands selects label mode

•

The label mode must be set for printing on the label paper and black mark paper.

Remarks:

■

This command is enabled in receipt mode.

■

This command can activate the label mode even if the receipt mode is predefined by the memory switch(Msw8-5).

However, since the mode specified by the memory switch(Msw8-5) is set to the default mode, the receipt mode
becomes effective after the printer reset or power cycling is executed.

■

The memory switch(Msw8-5) should be enabled to maintain the label mode after the printer reset or power cycling.

■

Once the printer has entered the label mode, it is necessary to perform the procedures as follows for the proper

operation:

•

Executing the automatic calibration to figure out the location of each label or black mark paper.

•

Readjusting the printing position by pressing paper Feed button or opening/closing the printer cover.

Differences:

None

Содержание SPP-R200II




















































































































































Результаты поиска

Содержание SPP-R200II

Отзывы:

Похожие инструкции для SPP-R200II

Бренды по названию

Популярные бренды

BIXOLON SPP-R200II, Руководство по управлению

Результаты поиска

Содержание SPP-R200II

Отзывы:

Похожие инструкции для SPP-R200II

Бренды по названию

Популярные бренды