background image

74

40016512

75

11/2017

COPY/PASTE FUNCTION (help for programming)

mode

boost

mode

boost

mode

boost

mode

boost

mode

boost

mode

boost

mode

boost

mode

boost

Long press on 

P1P2:

 back to

previous day, 

copies the current 

daily programme.

Long press on 

mode: 

move to

next day, copies

the current daily 

programme.

8. Maintenance and troubleshooting tips

8.1 Routine maintenance operations

High-quality materials and surface treatment protect your appliance against corrosion and 

impacts.

To maximise the service life of your appliance, we recommend you take the following precau-

tions:

 

- Never use abrasive or corrosive products on the outer surfaces of the appliance (except the  

 

electrical parts); use warm, soapy water.

 

- For the casing of the control unit and the remote control, use a dry (solvent-free) cloth.

8.2 Troubleshooting

Despite all our efforts in manufacturing our products, you may encounter some easy-to-solve 

operating failures. In this case, please consult the table below to find our suggested solution.

Nonetheless, should you fail to solve the problem encountered, please contact your supplier's 

after-sales service for assistance.

Problem

Diagnosis

Procedure

The appliance is not 

heating.

The temperature setting on the 

remote control is incorrect.

Check the remote control is set to ask 

the appliance to start heating (see 

chapter 5.2

).

The mixed appliance has not 

filled with water properly.

Check the filling of the appliance (see 

chapter 3.2

).

The appliance is operated by a 

programming unit.

See the programming unit manufac-

turer's manual.

The load shedder is enabled 

and has shut down heating on 

the appliance.

Wait for load shedding to finish.

The appliance has not be

paired with the remote control 

(the        icon is not displayed 

on the remote control screen).

Remove the batteries from the 

remote control, wait a few seconds, 

then replace the batteries and pro-

ceed with pairing (see 

chapter 4.1

).

An open window detected

(       icon flashes)

Turn off the window opening

detection function (see

 chapter 5.5

parameter 1).

The LED is flashing yellow: 

default.

Contact your installer.

Содержание 40016512






















Отзывы: