BIRD SiteHawk SK-200-TC Скачать руководство пользователя страница 62

Страница: 62 / 65

Bird SiteHawk Operation Manual

15. Launch the SiteHawk App.
16. Load the updated Cable List. See

“Recall Cable List” on page

Firmware Update

Go to http://www.birdrf.com/Products/Test and Measurement/Analyzers/
Cable-Antenna-Analyzers/

Scroll down to the Downloads.

Click on the Firmware link.

Note:

Ensure you are downloading the firmware for correct Site-

Hawk model.

Download the SiteHawk-Firmware-XXX.apk update file.

Connect the USB drive to the PC.

CAUTION

Do not connect the unit to a PC USB port.

File transfer must be done using a USB Drive.

Transfer the SiteHawk-Firmware-XXX.apk update file to the USB drive.

Remove the USB drive.

Connect the USB drive to the USB adapter. See

Figure

51 on page

Connect the USB adapter to the SiteHawk Analyzer.

Содержание SiteHawk SK-200-TC


































































Результаты поиска

Содержание SiteHawk SK-200-TC

Отзывы:

Похожие инструкции для SiteHawk SK-200-TC

Бренды по названию

Популярные бренды

BIRD SiteHawk SK-200-TC, Руководство по эксплуатации

Результаты поиска

Содержание SiteHawk SK-200-TC

Отзывы:

Похожие инструкции для SiteHawk SK-200-TC

Бренды по названию

Популярные бренды