BIRD SiteHawk SK-200-TC Скачать руководство пользователя страница 59 | Manualshive

Страница: 59 / 65

background image

Maintenance

50

Delete Cable from Cable List

Note:

Only cables added by the user may be deleted using this

method.

1.

Press DTF icon.

2.

Press CableList option to display the Cable List. See

3.

Scroll to the bottom of the Cable List to see the cable to be deleted.

4.

Select the cable to be deleted.

5.

Press Delete button to delete cable.

Save Cable List

1.

Press DTF icon.

2.

Press CableList option to display the Cable List. See

3.

Press Save

Figure

47

Save Cable List Dialog Box

4.

Press File Name to give the Cable List a unique filename.

5.

Press SAVE to save the Cable List.

Recall Cable List

Note:

This procedure is used to load a Cable List different from

the Cable List currently displayed.

1.

Press DTF icon.

2.

Press CableList option to display the Cable List. See

3.

Press the Recall button. See

.

«
...
57
58
59
60
61
...
»

Содержание SiteHawk SK-200-TC


































































Отзывы:

Нет отзывов

Похожие инструкции для SiteHawk SK-200-TC

Бренд: Oakton Страницы: 4

Бренд: AR Страницы: 20

Бренд: QLA Страницы: 18

Бренд: TC Electronic Страницы: 20

LaserHybrid SB 360i

Бренд: Fronius Страницы: 104

Бренд: MRC Страницы: 14

Бренд: Tonghui Страницы: 65

HX3 Drawbar Expander Version 5

Бренд: KEYBOARDPARTNER Страницы: 11

Бренд: Roland Страницы: 224

Бренд: South Страницы: 54

Бренд: envea Страницы: 68

Бренд: Prosense Страницы: 35

PHOSPHAX indoor sc

Бренд: Hach Страницы: 140

Бренд: Lufkin Страницы: 17

Бренд: Major tech Страницы: 28

Bullhorn RM4200 Series

Бренд: American Innovations Страницы: 68

Бренд: Megger Страницы: 14

Бренд: ICP DAS USA Страницы: 7

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды