BIRD SiteHawk SK-200-TC Скачать руководство пользователя страница 58

Страница: 58 / 65

Bird SiteHawk Operation Manual

Edit Cable List

The Cable List contains a list of known cable values. These procedure provide
the steps necessary to edit the Cable List and select Cable Lists. The Cable List
that is preloaded on the SiteHawk is named CableList.ini.

Edit Cable List on SiteHawk

Add Cable to Cable List

Note:

cables in the default list cannot be changed using this

method.

Press DTF icon.

Press CableList option to display the Cable List. See

Figure

Figure

Cable List Dialog Box

Press Add button to add new cable.

Scroll to the bottom of the Cable List to see the new entry.

Press each cell for Cable name, Velocity, Cable Loss and Frequency to enter
the new cables information.

Figure

After cable information is entered press OK.

Содержание SiteHawk SK-200-TC


































































Результаты поиска

Содержание SiteHawk SK-200-TC

Отзывы:

Похожие инструкции для SiteHawk SK-200-TC

Бренды по названию

Популярные бренды

BIRD SiteHawk SK-200-TC, Руководство по эксплуатации

Результаты поиска

Содержание SiteHawk SK-200-TC

Отзывы:

Похожие инструкции для SiteHawk SK-200-TC

Бренды по названию

Популярные бренды