BIRD SiteHawk SK-200-TC Скачать руководство пользователя страница 38

Страница: 38 / 65

Bird SiteHawk Operation Manual

Select from the following marker options:

Add

Press Add to add a marker.

Delete

Pressing Delete will the active marker. If deleting a marker, select the marker
before opening the marker menu.

Freq

Indicates the current frequency position of the active marker. Press the Freq
field to enter a new position/frequency for the marker.

Note:

Any marker position can be dynamically changed by press-

ing and dragging the marker left or right on the display screen.

Step

Sets the frequency value the active marker will move when the Move Left or
Move Right buttons are pressed. Press the Step field to enter a value.

Moves the position of the marker left or right by the step entered.

Move Left

Press to move the active marker to the left. Each press will move the active
marker the value in the Step field.

Move Right

Press to move the active marker to the right. Each press will move the active
marker the value in the Step field.

Search Max

Press to move the active marker to the maximum value position on the trace.

Search Min

Press to move the active marker to the minimum value position on the trace.

DeltaMarker

Press to toggle delta marker function on and off.

MoveDelta

Press to move the delta marker indicator to highlight a specific delta marker.

Search Peak M1~M2

Press to move marker 3 to the peak signal between marker 1 and marker 2.

Содержание SiteHawk SK-200-TC


































































Результаты поиска

Содержание SiteHawk SK-200-TC

Отзывы:

Похожие инструкции для SiteHawk SK-200-TC

Бренды по названию

Популярные бренды

BIRD SiteHawk SK-200-TC, Руководство по эксплуатации

Результаты поиска

Содержание SiteHawk SK-200-TC

Отзывы:

Похожие инструкции для SiteHawk SK-200-TC

Бренды по названию

Популярные бренды