BIRD SiteHawk SK-200-TC Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 65

background image

1

Chapter 1

Introduction

The SiteHawk Analyzer is a multifunction test instrument for use in installation
and maintenance of wireless systems.

The SK-4500 has a frequency range of 1 MHz to 4.5 GHz. See

Analyzer Specifications” on page

for additional data on each SiteHawk

Model.

Antenna systems are tested by using a SiteHawk Analyzer to measure match
conditions. Data points measured across a user-specified frequency band or
distance range are graphed on a 1920 x 1080 pixel touch screen display area.

Power Meter Application

SiteHawk Analyzers include the Bird RF Meter Application. The Bird RF Meter is
an Android application designed to work with a wide variety of Bird Power
Sensors. To measure transmitter power, connect an external power sensor to
the SiteHawk. Power measurements verify and monitor the condition of a
transmitter system. For additional information and a list of compatible power
sensors, view the Bird RF Meter Help system.

«
...
8
9
10
11
12
...
»

Содержание SiteHawk SK-200-TC


































































Отзывы:

Нет отзывов

Похожие инструкции для SiteHawk SK-200-TC

DigitalFlow GF868

Бренд: GE Страницы: 80

Бренд: UEi Страницы: 20

Бренд: Hach Страницы: 138

Бренд: Omicron Страницы: 80

Бренд: DayTronic Страницы: 54

Бренд: Bacharach Страницы: 2

Бренд: Bachmann Страницы: 33

Бренд: Sanmenxia Страницы: 17

Бренд: SANKO Страницы: 25

Бренд: Samson Страницы: 2

Бренд: velocomp Страницы: 4

Бренд: Rabid Elephant Страницы: 18

Бренд: Circutor Страницы: 48

Бренд: Eno Scientific Страницы: 47

Combo meter P700 Pro

Бренд: AquaMaster Страницы: 20

Бренд: Endress+Hauser Страницы: 24

Бренд: Keithley Страницы: 338

Бренд: Vaisala Страницы: 11

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды