background image

Bird SiteHawk Operation Manual

3

SiteHawk Analyzer Specifications

Frequency Range

1 MHz to 4.5 GHz

Frequency Accuracy

±2.5 ppm

Frequency Resolution Setting

1 kHz

Output Power

–10 dBm

Reflected Amplitude Accuracy

–15 dB to 0 dB
–25 dB to –15 dB
–35 dB to –25 dB

±0.4 dB
±1.5 dB
±4.0 dB

Trace Noise Amplitude (IFBW 1kHz)

0.02 dB rms

Single Point Measure Time

1.0 ms

Data Points

51 to 3201

Measure Bandwidth

100 Hz to 30 kHz

Temperature Stability

0.01 dB/°F 
0.02 dB/°C

Return Loss Measurement Range

Resolution

0 dB to –60 dB
0.01 dB

VSWR Measurement Range

Resolution

1.0 to 65.0
0.01

Cable Loss Measurement Range

Resolution

0 dB to 30 dB
0.01 dB

DTF Range

0 to 5000 ft. 
0 to 1500 m.

Test Port Connector

Impedance

N-type, Female
50 ohms

Connector 

USB-C, USB 3.0

Dimensions (L × W × H)

7.7 x 3.6 x 2.4 in. 
195 x 90 x 60 mm

Weight 

1.98 lbs. 
0.9 kg

Maximum Input Power

+22 dBm

Maximum Input Voltage

50 V

Operating Temperature

14° to 131° F
–10° to +55° C

Storage Temperature

–40° to 176° F 
–40° to +80° C

Battery Charging Temperature

32° to 95° F
0 to +35° C

Altitude

Up to 15000 ft. 
Up to 4600 m

Humidity

95±5° max  
(non-condensing)

Содержание SiteHawk SK-200-TC


































































Отзывы: