BIRD SiteHawk SK-200-TC Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 65

background image

About This Manual

vi

About This Manual

This manual covers the operating and maintenance instructions for the
following models:

SK-4500-TC

Changes to this Manual

We have made every effort to ensure this manual is accurate. If you discover
any errors, or if you have suggestions for improving this manual, please send
your comments to our Solon, Ohio factory. This manual may be periodically
updated. When inquiring about updates to this manual refer to the part number
and revision on the title page.

Literature Contents

Introduction —

Describes the features of the Bird SiteHawk™, lists equipment

supplied and optional equipment, provides power-up instructions and
measurement settings.

Measure Match Mode —

Lists the steps to make match measurements, as

well as providing instructions for all functions available in Measure Match
mode.

Distance-to-Fault Measurements —

The DTF measurement shows the

location of any problems in the antenna system. This is shown in either feet or
meters from the cable end connected to the SiteHawk.

Utilities —

Describes built-in instrument utility features and how to use them.

Maintenance —

Lists routine maintenance tasks as well as troubleshooting

for common problems. Specifications and parts information are also included.

«
...
5
6
7
8
9
...
»

Содержание SiteHawk SK-200-TC


































































Отзывы:

Нет отзывов

Похожие инструкции для SiteHawk SK-200-TC

SMatrix DMX2400

Бренд: dallmeier Страницы: 12

Бренд: Hammond Страницы: 130

Бренд: Keithley Страницы: 343

Бренд: Keithley Страницы: 334

Бренд: La Crosse Technology Страницы: 2

Бренд: OBD Страницы: 5

Бренд: Emos Страницы: 76

Бренд: Hanna Instruments Страницы: 52

Recordall Series

Бренд: Badger Meter Страницы: 8

Бренд: RIDGID Страницы: 18

Бренд: LEM Страницы: 33

FlowStar2 LB 514

Бренд: BERTHOLD TECHNOLOGIES Страницы: 130

Бренд: Megger Страницы: 8

Бренд: Omega Страницы: 16

Бренд: A&D Страницы: 10

Бренд: Camlab Страницы: 28

Бренд: VOLTCRAFT Страницы: 8

Бренд: Lafayette Instrument Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды