BIRD SiteHawk SK-200-TC Скачать руководство пользователя страница 63

Страница: 63 / 65

Maintenance

Figure

USB Drive connections

10. Turn on the SiteHawk Analyzer.
11. Select “File Manager”.
12. Select “External USB storage”.

Figure

APK file selection

13. Select SiteHawk-Firmware-XXX.apk.
14. Follow the Installation instructions on the unit.

Customer Service

Any maintenance or service procedure beyond the scope of those in this
chapter should be referred to a qualified service center.

If the unit needs to be returned for any reason, request an Return Material
Authorization (RMA) through the Bird Technologies website. All instruments
returned must be shipped prepaid and to the attention of the RMA number.

Bird Service Center

30303 Aurora Road
Cleveland (Solon), Ohio 44139-2794
Fax: (440) 248-5426
E-mail:

[email protected]

For the location of the Sales Office nearest you, visit our Web site at:

http://www.birdrf.com

Содержание SiteHawk SK-200-TC


































































Результаты поиска

Содержание SiteHawk SK-200-TC

Отзывы:

Похожие инструкции для SiteHawk SK-200-TC

Бренды по названию

Популярные бренды

BIRD SiteHawk SK-200-TC, Руководство по эксплуатации

Результаты поиска

Содержание SiteHawk SK-200-TC

Отзывы:

Похожие инструкции для SiteHawk SK-200-TC

Бренды по названию

Популярные бренды