Bioloid Robotis Скачать руководство пользователя страница 14

Страница: 14 / 142

User’s Guide

Execution

If you press the start button during standby mode the CM-5 unit will go into the

mode that you have selected. To go back into standby mode you can press the

mode change button or turn the power switch off and then back on again.

TIP

The mode change button is the reset button for the CPU inside the CM-5 unit.

Therefore, when the power is on, the CM-5 will go back to standby mode

whenever the mode change button is pressed.

Serial Cable

In order to communicate with a PC, the CM-5 unit has to be connected to it using

a serial cable.

When using a laptop: Most laptops do not have a serial port, thus you will have to

purchase and use a USB to serial converter device. USB2Serial can be purchase

at local computer stores.

Status Display LED

There are the four LEDs that indicate the status of the CM-5 unit. The definitions

of each are as follows.

Power: If the power is on, this LED will be on. The LED will blink when the batteries

inside the CM-5 unit are charging. Recharging starts when the SMPS is connected

to the power jack and the

○

button is pressed in standby mode.

TXD: This LED is on when the CM-5 unit is transmitting data.

RXD: This LED is on when the CM-5 unit is receiving data.

AUX: This LED is assigned for user programming. It can be turned on or off with the

behavior control program.

Direction Buttons

These buttons are also assigned for user programming like the AUX LED.

Содержание Robotis















































































































































Результаты поиска

Содержание Robotis

Отзывы:

Похожие инструкции для Robotis

Бренды по названию

Популярные бренды

Bioloid Robotis, Руководство пользователя

Результаты поиска

Содержание Robotis

Отзывы:

Похожие инструкции для Robotis

Бренды по названию

Популярные бренды