Bioloid Robotis Скачать руководство пользователя страница 139

Страница: 139 / 142

User’s Guide

10-2. Dynamixel AX-12 Program Update

AX-12 program update is a function that was added from the 1.26 version

of“Behavior Control Programmer.” Thus, users who are using versions below

1.26 should visit

www.robotis.com

and download the latest version and install it.

To see what version is installed, go to “help -> Behavior Control Programmer

Information.”

<Note: Make sure that CM-5 is at least Ver. 1.13>

AX-12 program is updated in behavior control programmer. Only versions above

Ver 1.13 are applicable. Thus, if you have versions below Ver 1.13, go to

www.robotis.com

and download the latest CM-5 program and run the CM-5

upgrade by referring to the “10-1. CM-5 Program Upgrade.” To see the version

of CM-5, refer to the“Robot Terminal” of “8. 1. Setting the ID and Dynamixel

Search.”

Step 1

As shown below, connect to the PC and CM-5 and turn on the power. At this point,

AX-12 must be connected to the CM-5 to update. Also, pre-assembled robot can

be connected at this time. AX-12 that will be updated must have ID between 1 and

19. If there is ID that exceed this range, correct it before running update. Also,

keep in mind that AX-12 that has redundant ID will not update properly.

Connect to the CM-5

Connect to the PC

139

Содержание Robotis















































































































































Результаты поиска

Содержание Robotis

Отзывы:

Похожие инструкции для Robotis

Бренды по названию

Популярные бренды

Bioloid Robotis, Руководство пользователя

Результаты поиска

Содержание Robotis

Отзывы:

Похожие инструкции для Robotis

Бренды по названию

Популярные бренды