manualshive.com logo in svg

BIO RAD PowerPac Universal Power Supply, Инструкция по эксплуатации

Поделиться
Скачать
BIO RAD PowerPac Universal Power Supply Скачать руководство пользователя страница 20

Page | 12 

PowerPac Universal Power Supply Instruction Manual

 

3.3 Manual Mode Operation 

This section describes how to program and perform a run in Manual mode. 

The Manual mode allows you to program and start a single-step run with a minimum 

number of keypad touches. The settings for a Manual mode run are saved as soon as 

you either execute the run by pressing the 

 key or return to the Home screen by 

pressing the 

 key, and will persist until you implement new parameters in Manual 

mode. Manual mode settings are not affected by cycling power or by executing stored 

runs using the Method operating mode (see 

Section 3.4

). 

Step  Procedure 

Description 

1.    Set up the power supply.  Refer to 

Section 3.1

 for instrument setup. 

2.    Select the Manual mode. 

 

On the Home screen, press the MANUAL soft key to perform 

a single-step run in Manual mode. 

 

NOTE:

 To create and run with a multi-step method, press 

METHODS and refer to 

Section 3.4

 for instructions. 

3.    Select the control 

parameter (Constant). 

 

Use the V/mA/W soft key to select the control parameter 

(volts, milliamps, or watts) according to your preference. 

Each press of the V/mA/W soft key cycles through the 

parameters. The selected parameter (Constant) appears on 

the left in large bold text, and is set to its minimum value. The 

limit parameters (Limits) appear on the right in smaller text on 

two lines, and are set to their respective maximum values.  

Содержание PowerPac Universal Power Supply











































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды