Bio-Logic PURE WATER PACK BIO 1.5 PWP, Руководство пользователя

Страница: 7 / 20

7
f
auCet
i
nstallation
C
ont
.
1. Select faucet location.
• Make sure the faucet is far enough away so not to interfere with the regular faucet or any other attachments.
• If mounting faucet on the countertop, make certain the spout of the faucet will reach over the sink.
• Check underneath the sink/countertop for any obstructions and for tool clearances required for mounting the faucet.
• Make certain the faucet will fit flat against the sink/countertop, so 1-7/8 inch rubber washer will seal against chrome
base plate and sink/countertop.
2. Mark the center of the faucet location.
To avoid possibly damaging sink and/or countertop, consult a qualified plumber or installer,
special tools may be required for drilling porcelain, stainless steel, tile, etc.
3. Using appropriate tools for particular sink or countertop construction, make a 1/2 inch diameter mounting hole.
4. Install the 1-1/4 inch rubber washer onto the faucet, followed by the chrome base plate, and finally the 1-7/8 inch rubber
washer. These parts must be installed onto the faucet before mounting the faucet to the sink or countertop.
5. Install faucet into the mounting hole. From under the sink install the 1-3/4 inch washer, the locking washer and thread the
9/16 inch nut onto the faucet. Align the faucet to desired position, and firmly tighten the nut.
6. Install John Guest
TM
Tubing Connector on to the inlet of the faucet. Insert 1/4 inch OD tubing into the end of tubing
connector. See “
Tubing Installation
”.
s
ystem
i
nstallation
IN ORDER TO PERFORM THIS TASK, BE SURE TO WEAR THE FOLLOWING SAFETY
EQUIPMENT: SAFETY GOGGLES OR A FACE SHIELD, AS WELL AS GLOVES
1. Once a suitable location, for the system, has been chosen, mark the location of the mounting screws, using the holes on the
mounting bracket as a template.
2. Using appropriate fasteners, for the type wall chosen, mount the system through the holes of the mounting bracket.
3. Tubing Connections:
a. Run the tubing, connected to the saddle valve, to the inlet fitting of the sediment filter.
b. Run the precut 24” tubing from the outlet of the carbon filter, to the inlet of the
Bio-Logic
®
water purifier.
c. Run the tubing from the faucet to the outlet of the Bio-Logic
®
water purifier. Measure, cut tubing. The tubing must be
cut square, free of burrs and sharp edges. Leave enough slack in the tubing so the system can be easily
removed, if necessary.
4. Turn on the faucet, supplied by the Pure Water Pack
TM
system. NOTE : Lifting the handle, of the faucet, will lock the
faucet in the “ON” position, while holding the handle down the faucet is “ON”, the faucet will shut off when the handle is
released. Slowly open the saddle valve, by turning the “T” handle counter-clockwise until fully open, and allow the system to
fill with water.
5. Once water begins to flow from the faucet, allow water to run for several minutes until it is clear with no air bubbles. Turn off
the faucet and check the system for leaks. If leaks occur see “Troubleshooting” section. If no leaks occur, proceed to install
the ultraviolet lamp.
6. Unpack the lamp and ballast. While holding lamp end, carefully push lamp socket on. Carefully slide lamp straight into the
quartz sleeve, without angling. Push the End Cap on, over the static gland nut. Attach the ground connector to the grounding
tab of the chamber.
To ensure proper operation and safety of the purifier, your unit must be connected
to a known good ground.
Lamp and quartz sleeve are easily damaged. Exercise care when handling.
7. For 120v 50/60Hz operation using ballast no. 10-0518A and 230v 50/60Hz using ballast 10-0514A, plug ballast into
an approved Ground Fault Circuit Interrupt (GFCI) receptacle. Where a 2-prong or unprotected 3-prong receptacle is
encountered, it must be replaced by a properly grounded Ground Fault Circuit Interrupt (GFCI) receptacle. Installation must
be in accordance with the National Electrical Code and any local codes and ordinances by a qualified electrician. For 12v DC
operation, The ballast must be wired to an adequate 12v DC source with appropriate gauge wire for the voltage and current. It
is recommended that the ballast have a dedicated run to the 12v source, and protected by either a fuse or circuit breaker.
Step 7 Continued on Page 8