background image

12

Q

uartz

 s

leeVe

 i

nstallation

, C

leaning

 

or

 r

ePlaCement

Figure 8 - Quartz Sleeve Cleaning or Replacement

Step 6 - Remove Quartz Sleeve

Step 5 - Remove Washer & O-Ring  

from each end

Step 4 - Remove Gland Nut From Each End

IN ORDER TO PERFORM THIS TASK, BE SURE TO WEAR THE FOLLOWING SAFETY 

EQUIPMENT: SAFETY GOGGLES OR A FACE SHIELD, AS WELL AS GLOVES

1. 

  

  Disconnect power to water purifier.

•  For 120v 50/60Hz version using ballast no. 10-0518A or 230v 50/60hz version using ballast no. 10-0514A, remove 

the ground connector from the chamber, and go to the next step.

2.  Shut off water supply to water purifier via inlet and outlet shut off valves and drain chamber, if possible.
3.  Follow the steps in 

“Lamp Installation or Replacement”

 to remove lamp. 

Lamp and quartz sleeve are easily damaged. Exercise care when handling.

4.  Unscrew static gland nuts from each end of the chamber. Avoid striking quartz sleeve with static gland nut.
5.  Remove Teflon

®

 washer and O-Ring from both ends of quartz sleeve. Teflon

®

 washer will sometimes remain within the static 

gland nut. If so, remove Teflon

®

 washer from static gland nut before proceeding.

6.  Carefully remove quartz sleeve from chamber. 

NOTE: It is advisable to support the quartz sleeve on the opposite end 

with your finger so that it does not drop to the bottom of the chamber as it slides into the chamber.

7.  Once the quartz sleeve is removed, clean with alcohol or a mild, non-abrasive detergent. Stubborn stains usually can be 

removed with a dilute hydrochloric acid. 

NOTE:

 

Follow all manufacturer’s instructions and precautions 

when handling chemicals.

8.  Reassemble in reverse order. Make sure the quartz sleeve protrudes an equal distance past each threaded nipple. Be sure 

O-Rings are placed on quartz sleeve before Teflon

®

 washer.

9.  Tighten static gland nuts firmly by hand only, 

DO NOT USE HAND TOOLS

. Tightening with hand tools is likely to cause 

quartz sleeve to break.

10. 

Slowly

 restore water supply to water purifier and check for leaks.  

(Continued on Page 13)

5.  Reinstall lamp in reverse order.

  Germicidal ultraviolet rays are harmful to eyes and skin. Do not restore power to water purifier 

until lamp and both 

EASY-OFF

TM

 End Caps have been properly reinstalled.

6.  Reattach the ground connector to the grounding tab of the chamber, and restore power to the system.

Содержание PURE WATER PACK BIO 1.5 PWP





















Отзывы: