BINMASTER NCR-80 Скачать руководство пользователя страница 42

Страница: 42 / 82

NCR-80 Four-wire 4-20 mA/HART

925-0332 Rev B

6 Set up the sensor with the display and adjustment module

The following languages are available:

●

German

●

English

●

French

●

Spanish

●

Russian

●

Italian

●

Dutch

●

Portuguese

●

Japanese

●

Chinese

●

Polish

●

Czech

●

Turkish

In the delivery status, the NCR-80 is set to the ordered national language.

In this menu item you can define the way measured values are indicated on the display.

The default setting for the display value is "

Percent

The display and adjustment module has a backlight for the display. In this menu item you can

switch the lighting on or off. You can find the required operating voltage in chapter "

Technical

data

In delivery status, the lighting is switched on.

In this menu item, the device status is displayed.

The min. and max. measured value, the measurement certainty as well as the min. and max.

electronics temperature are stored in the sensor. The values are displayed in menu item "

Peak

value

" or "

Further peak values

A reset menu is opened with the

[OK]

key in the respective peak value window:

With the

[OK]

key in the reset menu, the peak values are reset to the current measured value.

Содержание NCR-80



















































































Результаты поиска

Содержание NCR-80

Отзывы:

Похожие инструкции для NCR-80

Бренды по названию

Популярные бренды

BINMASTER NCR-80, Руководство по эксплуатации

Результаты поиска

Содержание NCR-80

Отзывы:

Похожие инструкции для NCR-80

Бренды по названию

Популярные бренды