10/24
3)
In order to assemble the particular of the piece of furniture, use a stable surface, without asperity
(in order to avoid scratches of the piece of furniture). Insert the base in the inferior part of the piece
of furniture inside the proper guides, and watching out for the correct position (front-back and
superior-inferior side): please take as reference the figure n.1. Fix the base to the piece of furniture,
assuring it with special screws:
- 4 screws with nut (see fig.1 details "A") to be obviously screwed in the correct way
- two screws, fixing the base and the front (see fig.1 detail "B") to be screwed in the correct way
- two screws, fixing the base and the "diaphragm" (see fig.1 detail "B") to be screwed in the correct
way
4)
Fix the cover to the piece of furniture by screwing the 2 hinges through special autofilettanti screws
(see fig.2 detail "C").
5)
This device must only be powered with LPG gas in a 15-kg cylinder and this must be equipped
with a pressure regulator and flexible tube: The pressure regulator must have a fixed calibration of
30 mbar conforming to EN12864 and the flexible rubber tube must be marked UNI-CIG 7140, with
a length of 50 cm (and not longer than 60 cm); the latter must be attached with metal bands of
suitable size and needs to be replaced by the date stamped on it (fig.2-3).
6)
The heater must be provided with a regulator and hose: make sure they are included in the supply.
The flexible hose must be checked regularly whenever the cylinder is replaced to be sure it has no
scratches or cuts and that it is in a perfect state. It must be replaced in any case before the expiry
date stamped on the hose itself.
7)
Connect the flexible tube to the hose union of the pressure regulator and to that of the tap, making
sure that the metal bands are tight and paying particular attention not to tamper with or damage any
component or fitting.
8)
Before connecting the cylinder, make sure that its tap is closed and that there are no open flames
(lit oven, etc.) in the place where you are working. Screw the pressure regulator onto the cylinder,
keeping these warnings in mind:
A)
check that the gasket seal is in good condition
B)
attach the regulator to the tap, screwing the nut tightly counterclockwise.
C)
carefully check that there is no gas leaking from the connection using soapy water: if there
is a leak, bubbles will form; tighten the connection more or seek professionally qualified
service.
Warning: do not check for gas leaks when the appliance is hot, but wait until it is cold.
9)
Place the cylinder in its compartment, taking care that the tube is not twisted or choked and isn't
touching hot parts.
10)
Hook the rear cylinder cover on the cabinet, insert the two hooks in the respective holes of the
cabinet and put the wing screws (fig.3).
11)
To replace the cylinder, make sure that its tap is closed and that there are no open flames (lit
oven, etc.) or sources of heat in the place where you are working; we recommend that you check
that the gasket seals of the regulator and flexible rubber tube are in good condition and replace
them, if necessary.
12)
To not mishandle the connections or other components.
13)
Do not turn the cylinder upside down to completely use its contents: this releases liquid residues
left in the tank that will irreparably damage the heater.
14)
Do not disconnect the pressure regulator from the cylinder when the cylinder tap is open.
15)
The manufacturer will not be responsible if one of the above points is disregarded.
USE (See Fig.4)
Controls for switching on and adjustment are found at the top of the appliance.
1.
Open the cylinder valve.
2.
Press the valve knob down hard and turn anti-clockwise until reaching the ON position
marked “
” (see fig.4 “pos.A”), thus lighting the pilot flame; to keep the flame alight, the
Содержание K80.NE
Страница 2: ...2 24 Fig 1 Fig 2 Fig 3...
