BFT ALTAIR-P, Инструкция по установке и эксплуатации

Страница: 13 / 40

ALTAIR-P - Ver. 03 -
13
D81
1506_03
INSTALLATION MANUAL ENGLISh
6.4) Language Menu (
Language
)
Allows you to set the language on the display programmer.
5 languages are available:
- ITALIAN (
itA
)
- FRENCh (
FRA
)
- GERMAN (
DEU
)
- ENGLISh (
ENG
)
- SPANISh (
ESP
)
6.5) MENU DEFAULT (
DEFAULT
)
Restores the preset default values on the control unit.
6.6) DIAGNOSTICS AND MONITORING
The display on the ALTAIR-P panel shows some useful information, both
during normal operation and in the case of malfunctions.
Diagnostics:
In the case of malfunctions, the display shows a message indicating which
device needs to be checked:
STRT = START input activation
STOP = STOP input activation
PHOT = PHOT input activation
PED
= input activation PEDESTRIAN
OPEN = OPEN input activation
CLS
= CLOSE input activation
7) RADIO TEChNICAL SPECIFICATIONS
Receiver output channels:
- output channel 1, if activated, controls a START command.
- output channel 2, if activated, controls the excitation of the 2nd radio
channel relay for 1s, or activates the pedestrian function, depending on
the setting.
Transmitter versions which can be used:
all Rolling Code transmitters compatible with .
7.1) ANTENNA INSTALLATION
Use an antenna tuned to 433Mhz.
For Antenna-Receiver connection, use RG58 coaxial cable.
The presence of metallic masses next to the antenna can interfere with radio
reception. In case of insufficient transmitter range, move the antenna to a
more suitable position.
7.2) RECEIVER CONFIGURATION
Cloning operations can be carried out with the special
universal pal-
mtop programmer only. The on-board receiver combines characteristics
of utmost safety in copying variable code (rolling code) coding with the
convenience of carrying out transmitter “cloning” operations thanks to an
exclusive system.
Cloning a transmitter means creating a transmitter which can be automatically
included within the list of the transmitters memorised in the receiver, either
as an addition or as a replacement of a particular transmitter.
Cloning by replacement is used to create a new transmitter which takes the
place of the one previously memorised in the receiver; in this way a specific
transmitter can be removed from the memory and will no longer be usable.
Therefore it will be possible to remotely program a large number of additional
transmitters or, for example, replacement transmitters for those which have
been lost, without making changes directly to the receiver.
When coding safety is not a decisive factor, the on-board receiver allows
you to carry out fixed-code additional cloning which, although abandoning
the variable code, provides a high number of coding combinations, there-
fore keeping it possible to “copy” any transmitter which has already been
programmed .
7.3) PROGRAMMING
Transmitter storage can be carried out in manual mode, or by means of the
universal palmtop programmer which allows you to create installations in
the “collective receivers” mode, as well as manage the complete installation
database using the
EEdbase
software.
The receiver is programmed by connecting universal palmtop programmer
to the
ALTAIR-P
control panel, using the
UNIFLAT
and
UNIDA
accessories,
as shown in fig. 4.
7.4) MANUAL PROGRAMMING
In the case of standard installations where advanced functions are not
required, you can proceed to manual storage of the transmitters, making
reference to fig. B for basic programming.
- If you wish the transmitter to activate output 1 (START) by means of key1,
key2, key3 or key4, enter the transmitter in menu “Start key”, as in fig. B.
- If you wish the transmitter to activate output 2 (2nd radio channel relay)
by means of key1, key2, key3 or key4, enter the transmitter in menu “2nd
ch. key”, as in fig. B.
Note:
Hidden key P1 appears differently depending on the transmitter
model.
For transmitters with hidden key, press hidden key P1 (fig. B1). For transmit-
ters without hidden key, the key P1 function corresponds to simultaneously
pressing the 4 transmitter keys or, after opening the battery compartment,
bridging the two P1 points by means of a screwdriver (fig. B2).
IMPORTANT NOTE: ATTACh ThE ADh ESIVE KEY LABEL TO ThE FIRST
MEMORISED TRANSMITTER (MASTER).
In the case of manual programming, the first transmitter assigns the key
code to the receiver; this code is necessary in order to carry out subsequent
cloning of the radio transmitters.
7.5) RADIO-TRANSMITTER CLONING
Rolling-code cloning / Fixed-code cloning
Make reference to the universal palmtop programmer Instructions and the
CLONIX Programming Guide.
7.6) ADVANCED PROGRAMMING: COLLECTIVE RECEIVERS
Make reference to the universal palmtop programmer Instructions and the
CLONIX Programming Guide.
8) SERIAL CONNECTION USING SCS1 BOARD (Fig.5)
The ALTAIR-P control panel allows several automation units (SCS1) to be
connected in a centralised way by means of appropriate serial inputs and
outputs. This makes it possible to use one single command to open and
close all the automation units connected.
Following the diagram in Fig.5, proceed to connecting all the
ALTAIR-P control
panels, exclusively using a telephone-type line.
Should a telephone cable with more than one pair be needed, it is indispens-
able to use wires from the same pair.
The length of the telephone cable between one appliance and the next must
not exceed 250 m.
At this point, each of the
ALTAIR-P control panels must be appropriately
configured, by setting a MASTER unit first of all, which will have control over
all the others, to be necessarily set as SLAVE (see logic menu).
Also set the Zone number (see parameter menu) between 0 and 127.
The zone number allows you to create groups of automation units, each one
answering to the Zone Master unit.
Each zone can only be assigned one
Master unit, the Master unit in zone 0 also controls the Slave units in
the other zones.
9) CONNECTION OF ThE ELECTRIC LOCK
EBP: see Fig. 6A
ECB: see Fig. 6B
N.B. The radio transmitters must be stored in the 2nd radio channel. The
output of the 2nd radio channel controls the “ME” board.
10) SCRAPPING
Warning: This operation should only be carried out by qualified person-
nel.
Materials must be disposed of in conformity with the current regulations.
In case of scrapping, the automation devices do not entail any particular risks
or danger. In case of materials to be recycled, these should be sorted out by
type (electrical components, copper, aluminium, plastic etc.).
11) DISMANTLING
Warning: This operation should only be carried out by qualified person-
nel. When the control unit is disassembled to be reassembled on another
site
,
proceed as follows:
• Disconnect the power supply and the entire electrical installation.
• In the case where some of the components cannot be removed or are
damaged, they must be replaced.
WARNINGS
Correct controller operation is only ensured when the data contained
in the present manual are observed. The company is not to be held
responsible for any damage resulting from failure to observe the
installation standards and the instructions contained in the present
manual.
The descriptions and illustrations contained in the present manual are
not binding. The Company reserves the right to make any alterations
deemed appropriate for the technical, manufacturing and commercial
improvement of the product, while leaving the essential product fea-
tures unchanged, at any time and without undertaking to update the
present publication.