Bettcher Quantum Flex Air 1000 Скачать руководство пользователя страница 91

Страница: 91 / 177

Maintenance

Manual No. 107193
November 1, 2018

Maintenance
Quantum Flex

Air Operating Instructions and Parts List

5-43

Inspection and Maintenance of Power Unit

(

Continued

)

Adapter Plate



Inspect the adapter plate for cracks or chips. Replace the adapter plate if damaged.



Inspect o-ring for nicks, cuts or tears. Replace the o-ring if damaged.

Muffler



Inspect the muffler for broken or protruding wires. Replace the muffler if damaged.



Muffler may be cleaned with parts cleaner to remove build-up. Replace muffler if
excessive build up prevents proper cleaning.

Retainer



Inspect the retainer for cracks or chips. Replace the retainer if damaged.



Inspect the retainer threads for damage. Replace the retainer if damaged.

Note:

Do not clean the muffler
while it is installed in the
power unit.

Adapter

Plate

O-Ring

COMPANY

CONFIDENTIAL

Содержание Quantum Flex Air 1000


















































































































































































Результаты поиска

Содержание Quantum Flex Air 1000

Отзывы:

Бренды по названию

Популярные бренды

Bettcher Quantum Flex Air 1000, Инструкция по эксплуатации и перечень запасных частей

Результаты поиска

Содержание Quantum Flex Air 1000

Отзывы:

Бренды по названию

Популярные бренды