Bettcher Quantum Flex Air 1000 Скачать руководство пользователя страница 28

Страница: 28 / 177

Instructions for Operation

4-6

Instructions for Operation
Quantum Flex

Air Operating Instructions and Parts List

Manual No. 107193
November 1, 2018

Power Unit / Head Assembly - Attachment and Adjustment

(Continued)

Step 4:

Power Unit



While holding the trimmer, pick up a

power unit.



Firmly push the power unit towards

the bottom of the spacer ring or
optional thumb support. Align the
power unit spline with the splines on
the frame.

NOTE: The handle can be adjusted to suit the operator and the work station by pulling the
power unit back away from the frame and re-locating it on another set of notches on the frame.

Step 5:

Attachment Screw



Insert the attachment screw in the
frame.



Tighten the attachment screw
FIRMLY, using the supplied hex
wrench.

NOTE:

Recommended torque of

50-60 lb-in (5.6-6.8 N-m) for
Small Tools and 115-140 lb-in
(13-16 N-m) for the Large Tools.

Power

Unit

Power Unit Splines

Frame Splines for
Power Unit

Hex Wrench

Attachment Screw

Frame

COMPANY

CONFIDENTIAL

Содержание Quantum Flex Air 1000


















































































































































































Результаты поиска

Содержание Quantum Flex Air 1000

Отзывы:

Бренды по названию

Популярные бренды

Bettcher Quantum Flex Air 1000, Инструкция по эксплуатации и перечень запасных частей

Результаты поиска

Содержание Quantum Flex Air 1000

Отзывы:

Бренды по названию

Популярные бренды