manualshive.com logo in svg

Bettcher Quantum Flex Air 1000, Инструкция по эксплуатации и перечень запасных частей

Поделиться
Скачать
Bettcher Quantum Flex Air 1000 Скачать руководство пользователя страница 63

 

Maintenance  

 

Manual No. 107193 
November 1, 2018 

 Maintenance  
 Quantum Flex

® 

Air Operating Instructions and Parts List 

5-15 

 

Blade Sharpening 

 

 

Sharp blades may cause cut injury! 
 
Always disconnect the air supply prior to servicing. 
 
For proper protection of hands, a protective glove 
should be used when operating this equipment and 
during the handling of blades. 

 

 

 

After sharpening, all abrasive dust must be 
completely removed from the handpiece.   
Disassemble the unit and carefully wash each piece 
with hot, soapy water and a small brush. 
 

Machine Sharpening 

The blade should be stoned or sharpened on a Whizard

®

 Model 210 Universal Blade Sharpener, 

Whizard

®

 Model 214 Blade Sharpener (International Only), or Bettcher

®

 AutoEdge at the end of 

each work day. Be sure to clean the blade first to remove all grease or meat particles which 
could coat the stone and greatly reduce its effectiveness. In the event the stone becomes coated, 
simply scrub it using hot, soapy water. 

 

Hand Stoning 
Models: 360, 625, 505, 850, 880, 1850, 1880, 1000, 1300, 1400 and 1500 

With the trimmer running, apply the flat side of the stone to the outside of the blade as shown in 
the illustration. The stone should be applied with the flat part of the stone resting on the flat part 
of the blade edge to be ground, using a "back and forth" motion.  Use the Special Whizard

®

 

Steel to finish sharpening the blade.  

 

 

 

 

 

 

WARNING

WARNING

 

 

SPECIAL STONE 

BLADE CUTTING 
EDGE 

SPECIAL STONE 

BLADE CUTTING 
EDGE 

COMPANY 

CONFIDENTIAL

Содержание Quantum Flex Air 1000


















































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды