Bettcher Quantum Flex Air 1000 Скачать руководство пользователя страница 26

Страница: 26 / 177

Instructions for Operation

4-4

Instructions for Operation
Quantum Flex

Air Operating Instructions and Parts List

Manual No. 107193
November 1, 2018

Power Unit / Head Assembly - Attachment and Adjustment

(Continued)

Step 1:

Grease Cup and Ring

•

Pick up the Quantum Flex

Air

Trimmer.

•

Pick up the grease cup and ring. Apply a
small amount of Whizard

Special

Grease to the frame o-rings.

•

With a twisting motion, install the grease
ring onto the frame over the o-rings.

Be careful not to
squeeze the o-rings out
of their grooves, or
they could be trapped
and damaged.

•

Rotate the grease cup to the desired position.

Step 2:

Spacer Ring

•

Select the spacer ring or optional thumb
support.

•

If the spacer ring is used

, Slide the spacer

ring onto the frame, small end first.

Grease
Ring

Frame

Frame O-rings (2)

Grease Cup

Spacer Ring

Frame

Small End

COMPANY

CONFIDENTIAL

Содержание Quantum Flex Air 1000


















































































































































































Результаты поиска

Содержание Quantum Flex Air 1000

Отзывы:

Бренды по названию

Популярные бренды

Bettcher Quantum Flex Air 1000, Инструкция по эксплуатации и перечень запасных частей

Результаты поиска

Содержание Quantum Flex Air 1000

Отзывы:

Бренды по названию

Популярные бренды