manualshive.com logo in svg

Bettcher Quantum Flex Air 1000, Инструкция по эксплуатации и перечень запасных частей

Поделиться
Скачать
Bettcher Quantum Flex Air 1000 Скачать руководство пользователя страница 60

 

 Maintenance

 

 

5-12 

Maintenance 
Quantum Flex

®

 Air Operating Instructions and Parts List 

Manual No. 107193  
November 1, 2018 

 

Daily Inspection and Maintenance of Handpiece 

 

 

Inspection of all parts for excessive wear is critical to 
ensure proper and safe operation. Vibration or lock-
up may occur as a result of the use of excessively 
worn parts. 
 
Sharp blades may cause cut injury! 
 
Always disconnect power and remove the tool from 
the driveline or flexshaft and casing assembly prior to 
servicing. 
 
Do not adjust handle or thumb support with the 
trimmer running, or with blade installed. 
 
After sharpening blade, all abrasive dust must be 
completely removed from the handpiece. 
Disassemble the unit and carefully wash each piece 
with hot, soapy water and a small brush. 
 
Prior to assembly, be sure all parts are clean and 
have been inspected for wear 

 

 

Blade 

 

Check for worn or chipped teeth. 

 

Check for damage to the cutting edge. 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

WARNING

COMPANY 

CONFIDENTIAL

Содержание Quantum Flex Air 1000


















































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды