5
Double
Double
Double
OPERATION INSTRUCTIONS
How to Add or Remove Salt?
Adding Salt
1. Switch on the filter to circulate the pool water.
2. Keep the chlorinator “OFF”.
3. Determine the amount of salt to be added according to the
Pool Salt Usage table.
4. Evenly and slowly pour in the salt around the inside perimeter
of the pool. To avoid clogging the filter, do not add salt through
the skimmer.
5. Brush the pool bottom to speed up the dissolving process. Do
not allow salt to pile up on the pool bottom. Run the filter 24
for hours to dissolve salt completely.
6. After 24 hours refer the Flow Status LED Indicator section to
check water flow status. If the water flow status is normal, you
can set the chlorinator to the desired operating time.
Removing Salt
If too much salt has been added, the “high” salt level Red LED
will light up. The only way to lower the salt concentration is to
drain and refill approximately 20% of the pool’s water until the
“high” salt level Red LED gose out and with the “good” salt level
Green LED lights up.
NOTE: After the salt is dissolved,
but before operating the
chlorinator be sure that:
• The filter pump/sand filter and the
chlorinator are connected to a
grounding type receptacle
protected by a residual current
device (RCD).
• The filter pump/sand filter
operates several minutes before
operating the chlorinator. This
removes air pockets and debris in
the water hoses.
• No air is trapped in any of the
hoses. Follow the filter
pump/sand filter manual to
release any trapped air.
1. On-off Button
This button turns the chlorinator on and off.
IMPORTANT:
Before starting the Flowclear Chlorinator follow
the steps below:
Step 1: First start the filter pump/sand filter pump.
Step 2: After chlorinator connect with power outlet, LED light
above switch button shows red. If the LED light shows green
or green with twinkle,press switch button make the LED light
turns red.
Step 3: Press the on/off button for 5 seconds then release,
after release the Chlorinator will emit three long beeps.
Step 4: on/off button remain red and the chlorinator will be
ready to use.
Step 5: Wait for 1 minute.
Step 6: Push the on/off button the led above become green
and the chlorinator will begin to work. Follow the instruction
point 2 for the time adjustment button.
NOTE:
If after step 6, from the LED above the on/off button
flashes green, repeat the operation again starting from step 2
NOTE:
When the LED on/off button is flashing green and all
other LED sare off, it means the chlorinatoris in stand-by
mode. The chlorinator goes into stand-by mode after the
operation time is completed.
2. Time Adjustment Bottons
Press and hold together the and buttons for less than
one second to lock/unlock the keypad. When the keypad is
unlocked, the operating time LED indicators will flash; when
the keypad is locked the LED indicator will stop flashing.
Press the button to increase the operating time 2 hours
Press the button to decrease the operating time 2 hours
NOTE:
The unit will automatically lock after no instructions for
5 seconds.
IMPORTANT:
When the operating time is set, to change the
operation time, follow the below instructions:
- Push the on/off button for less than one second and the LED
will become red
- Follow the instructions in point 1 “on-off button” from step 3
3. Operating Time LED Indicators
The green lights show the remaining hours in the daily
operating cycle.
4. Double Time Button
Pressing this button will double the working time shown on the
operating time LED, the LED above will light up if in double
mode.
5. Flow Status LED Indicator
Green
light indicates there is sufficient water flow turns to
produce chlorine.
Red
light indicates insufficient water flow, no chlorine will be
produced.
Note:
An alarm, with beeping and a red flashing light,
indicating the insufficient water flow will continue for 5
minutes.
After the 5 minutes, the light will continue flashing, however
the beeping will stop.
After 30 minutes, all lights will turn off
To restart the entire system, press the on/off button for no
more than 1 second
6. Salt Level Status LED Indicators
These LED lights indicate the salt level in the pool water.
Red: High.
The salt level is too high, no chlorine is produced,
salt needs to be removed from the pool water.
Green: Good.
The salt level is optimum, and chlorine is being
produced.
Yellow: Low
. The salt level is too low, no chlorine is
produced, need to add salt to the pool water.
Note:
An alarm, with beeping and a red/yellow flashing light,
indicating the high/low salt level will continue for 5 minutes.
After the 5 minutes, the light will continue flashing, however
the beeping will stop.
After 30 minutes, all lights will turn off
To restart the entire system, press the on/off button for no
more than 1 second
NOTE:
Refer to the Pool Salt Usage section for salt
concentration adjustment.
NOTE:
When the chlorinating cycle ends, only the LED above
the On-off button displays green flashing. The chlorinator will go
into a standby mode, and will turn itself back on in 24 hours to
continue its daily chlorine production.
IMPORTANT:
Never use the pool if chlorine level is more
than 3ppm. Do not operate the chlorinator while the pool is
in use or occupied.
• Always use a test trip to test the chlorine level before entering
or using the pool. If the chlorine level is too high, wait until the
chlorine level drops below 3ppm before using the pool or
operating the chlorinator.
• Heavy pool usage and higher temperatures may require higher
chlorine output (longer operating time) to maintain proper free
available chlorine residuals.
• If a power outage occurs or the power cord is unplugged for
more than 48 hours, then the chlorinator operating time will
have to be reset.
NOTE: LED indicater will not off under sleep mode if it has
been turned in before.
CHLORINATOR STATIONARY MOUNTING (OPTION)
Chlorinators are required to stay in a permanent upright position
according to the regulations in some areas. In this case, mount
the product to a platform as shown in the drawings.
For connection to filter pumps / sand filters with 1-1/2in. (38mm) hose size.
Connecting
Hose
Connecting Hose
Adaptor B
Adaptor B
Sand Filter
Filter Pump
Pool
A
Adaptor A
Water
Water
B
A
S-S-004379
