background image

Service and Maintenance

3–12

7KC Series Service Manual

d. From the outside of the door, install the lock chassis assembly. 

The outside rose and liner assembly should be flush with the 
door. Make sure the latch tabs engage the chassis frame and the 
latch tailpiece engages the retractor.

4. Test the lever operation to make sure that the latch tailpiece does 

not bind with the chassis retractor.

5. Reinstall the following components:

inside rose and liner (

page 3–5

)

levers (

page 3–4

).

T

ROUBLESHOOTING

This table summarizes the possible causes for certain lock problems. 
The causes are listed in the order of likelihood. (The most likely cause is 
first, and so forth.)

Figure 3.12

Adjusting the outside rose and liner assembly

Outside rose 
and liner

Rose locking pin

Hub

You notice…

Possible causes include…

You should…

Lever won’t return to its normal 
position.

There is binding between the lever 
and rose.

Make sure that the lock chassis is 
centered within the door 
(

page 3–11

).

Key spins freely, but won’t retract 
the latch or unlock the door.

Throw member is not installed.

Install the throw member.

Core doesn’t fit into the lever core 
hole.

Keyed lever is defective.

Replace the keyed lever (

page 3–2

).

Button doesn’t pop out as expected. Button retainer is damaged or bent.

Replace the button assembly 
(

page 3–8

).

Latch doesn’t retract.

a. Latch tailpiece is broken.

a. Replace the latch assembly.

b. Latch tailpiece didn’t engage the 

retractor correctly during 
installation.

b. Reinstall the lock chassis in the 

door (

page 3–6

).

Содержание 72KC









































Отзывы: