manualshive.com logo in svg

Bernina Bernette Funlock b44, Инструкция по эксплуатации

Поделиться
Скачать
Bernina Bernette Funlock b44 Скачать руководство пользователя страница 47

 

47

1

1

PLEASE NOTE:

Presser foot has been removed to show detail.

•  Inside Corner

 

–

Cut inside corner up to seam line 

(1)

 as shown.

 

–

Sew along seam line.

 

–

Sew up to end of fold. (Leave needle in fabric)

•  Pin Placement

 

–

Insert pins to the left of the presser foot. The 
pins will be easy to remove and are away from 
the cutting action of the knives.

 

–

Turn the fabric and lower the presser foot so 
that the upper knife is positioned in line with the 
cut edge.

 

–

Pull slack threads up, then start to sew.

   CAUTION:

Sewing over pins will damage and /or destroy 
the cutting edge of the knives.

•  Securing The Thread Chain

 

–

Thread a large eye, hand sewing needle (such 
as a tapestry needle) with the thread chain.

 

–

Insert the needle into the end of the seam to 
secure thread.

 

–

Raise presser foot. (Leave needle in fabric)

 

–

Spread fold and re–fold so that seam line is 
straight

Содержание Bernette Funlock b44

























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды