manualshive.com logo in svg

Bernina Bernette Funlock b44, Инструкция по эксплуатации

Поделиться
Скачать
Bernina Bernette Funlock b44 Скачать руководство пользователя страница 10

10

OFF

ON

2

1

2

3

6

4

5

1

Principal Parts behind the Looper 

Cover

PREPARATION TO SEWING

HOW TO OPEN LOOPER 

COVER

(1)

 Upper looper

(2)

 Upper knife (moveable)

(3)

 Standard presser foot

(4)

 Fixed position lower knife

(5)

 Lower looper

(6)

 Rolled Hem lever

Power Switch

 

–

Connect the controller/electric plug to the 
machine receptacle.

 

–

Plug power line into electric outlet.

 

–

Push " l " mark side to turn "ON" 

 

–

Push "O" mark side to turn "OFF" 

1.  Push the cover to the right as far as it will go.

2.  Pull cover down toward you. 

   CAUTION:

Be sure to turn off power switch.

   CAUTION:

Be sure looper cover is closed when sewing.

   CAUTION:

Use only foot controller provided with this 
machine. (Type 4C–316B for USA & CANADA 
only). Be sure to make reference to “Warning” 
on following Page.

Foot Controller

 

–

To run the machine and control the speed, 
press the controller.

 

–

The harder you press, the faster the machine 
will sew.

 

–

To stop the machine from sewing, remove your 
foot from the controller

Содержание Bernette Funlock b44

























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды