manualshive.com logo in svg

Bernina Bernette Funlock b44, Инструкция по эксплуатации

Поделиться
Скачать
Bernina Bernette Funlock b44 Скачать руководство пользователя страница 12

12

PREPARATION FOR 

THREADING

Setting up the Retractable thread 

stand

 

–

Take out the retractable thread stand from the 
top of Styrofoam, and insert it as shown on the 
left illustration.

 

–

This machine is shipped with the retractable 
thread stand on the top of styrofoam.

 

–

Fully extend the retractable thread stand.

 

–

The two joints on the telescope will click into 
place when they are correctly positioned.

 

–

Center the retractable thread stand above the 
spool pins.

 

–

Place thread over the cone adapters on the 
spool pins.

Spool net

When using synthetic threads that easily spill off the 
cone, slip the spool net 

(1) 

furnished with the machine 

over the thread from the bottom of the cone leaving 
the thread end hanging free at the top the spool net as 
shown at left.

Spool Cap

When using a regular thread spool, fit the spool cap 

(2)

 supplied with the machine onto the thread spool 

(3)

 as shown at left.

3

2

1

Содержание Bernette Funlock b44

























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды