background image

Introduction.

W

elcome  to  the  Suspended  Oil  fi red  Unit  Heater  Range. 
Local regulations may vary in the country of use and it is 

the installers responsibility to ensure that such regulations are
satisfi ed

All  installation,  assembly,  commissioning  and  service 
procedures  must  be  carried  out  by  suitable  qualifi ed 
competent  persons  to  the  statutory  regulations  in  the
country of use.

When  installing,  commissioning  and  servicing  is  undertaken 

on  these  heaters  due  care  and  attention  is  required  to
ensure that working at height regulations are adhered to at the 
mounting heights specifi ed. 

All Dimensions shown are in mm unless  

 

PLEASE  READ

  this  document  prior  to  installation  and 

use.  The  safety  of  this  heater  is  guaranteed  only  by  the 

correct usage in accordance with these instructions, therefore 
it is recommended that they are retained for future reference.

The manufacturer reserves the right to alter specifi cations without 
prior notice.

Any reference made to Laws, Standards, Directives, Codes of Practice or other recommendations governing 
the application and installation of heating appliances and which may be referred to in Brochures, 
Specifi cations, Quotations, and Installation, Operation and Maintenance manuals is done so for information 
and guidance purposes only and should only be considered valid at the time of the publication. 
The Manufacturer cannot be held responsible from any matters arising from the revision to or introduction 
of new Laws, Standards, Directives, Codes of Practice or other recommendations.       

Bio fuel statement.

All our oil fi red heater products are confi gured for use on both Class D light distillate fuel oil.

As a result of recent changes made to European legislation regarding the specifi cation of class D heating oil 
to allow for the inclusion of 7% FAME (Fatty Acid Methyl Ester) i.e. bio fuel and eff ective from early 2011, all 
oil fi red air heater products and installations maybe aff ected.

From April 2011 all our 

Suspended Oil fi red Unit Heaters 

will be fi tted with Riello burners which are bio fuel

compatible for blends up to 10%.

Please note that the use of bio fuels may give rise to a number of installation issues, to both new and
existing plant which could aff ect the warranty of the burner. We recommend that you familiarise yourself 
with current information from both the burner manufacturer Riello and OFTEC.

IMPORTANT NOTICE TO INSTALLERS

Installers should satisfy themselves that the oil pipework installation is carried out in accordance 
with all current legislation, Codes of Practice and recommendations . 

Содержание OUH 2 100













































Отзывы: