7.
Replacement Parts.
Note
It is recommended that only suitably competent persons are
allowed to undertake replacement of parts.
7.1
Burner.
•
Disconnect electrical supply to the heater and shut off
oil supply.
•
Disconnect fuel line.
•
Open the controls compartment door.
•
Remove the oil fi red burner cover.
•
Detach electrical connections via plugs.
•
Using an 13mm spanner, remove the nut holding the
unit to the burner fl ange.
•
Withdraw the burner from the throat of the heat
exchanger.
•
Replace in reverse order.
7.2
Controller
•
Disconnect electrical supply to the heater.
•
Open the controls compartment door.
•
Remove the oil fi red burner cover.
•
Remove the screw fi xing the controller to the base
and withdraw controller.
•
Replace in reverse order.
7.3
Electrode Assembly
•
Disconnect electrical supply to the heater.
•
Open the controls compartment door.
•
Remove the oil fi red burner cover.
•
Using an 13mm spanner, remove the nut holding the
unit to the burner fl ange.
•
Withdraw the burner from the throat of the heat
exchanger, support on bracket/fl ange lugs.
•
Remove the fi xing screw(s) holding the End Cone and
withdraw from burner head.
•
Loosen the screw clamping the electrodes.
•
Replace in reverse order.
7.4
Nozzle
•
Disconnect electrical supply.
•
Open the controls compartment door.
•
Remove the oil fi red burner cover.
•
Using an 13mm spanner, remove the nut holding the
unit to the burner fl ange.
•
Withdraw the burner from the throat of the heat
exchanger.
•
Remove the fi xing screw(s) holding the End Cone and
withdraw from burner head.
•
Using a 17mm spanner, remove the nozzle
•
Replace in reverse order.
7.5
Photocell
•
Disconnect electrical supply.
•
Open the controls compartment door.
•
Remove the oil fi red burner cover.
•
Remove the screw fi xing the controller to the base
and withdraw controller.
•
Withdraw photocell from front of controller.
7.6
Oil Pump
•
Disconnect electrical supply to the heater and shut off
oil supply.
•
Disconnect fuel line.
•
Disconnect single pipe (or 2 pipe) oil lines from the
pump.
•
Open the controls compartment door.
•
Remove the oil fi red burner cover.
•
Remove the nut securing the coil and withdraw coil.
•
Remove the 3 screws fi xing the pump onto the motor
shaft.
•
Withdraw pump carefully
•
Replace in reverse order.
Содержание OUH 2 100
