BendPak MD-6XP Скачать руководство пользователя страница 33

Страница: 33 / 44

MD-6XP Mid-Rise Scissor Lift

P/N 5900108 — Rev. F — March 2020

Lubricate the Lift

The following drawing shows the lubrication points on the Lift.

Maintenance

⚠

DANGER

Before performing maintenance on your Lift, make sure it is disconnected from
power. The Lift uses electrical energy; if your organization has Lockout/Tagout
policies, make sure to implement them before performing any maintenance. If you

come into contact with high voltage/current, you could be injured or killed.

To maintain your Lift

•

Daily

: Keep the Lift clean. Wipe up any oil spills, clean any dirt.

•

Daily

: Make a visual inspection of all moving parts and check for damage or excessive wear. If

you find any damaged or worn parts, take the Lift out of service until they are replaced.

•

Daily

: Make sure the Safety Locks are in good operating condition. If you find that the Safety

Locks are damaged or excessively worn, take the Lift out of service until they are replaced.

not use your Lift if the Safety Locks are damaged or excessively worn

•

Weekly

: Check all controls to make sure they are functioning normally.

•

Weekly

: Check all labels on the unit. Replace them if they are illegible or missing.

•

Monthly

: Lubricate the grease fittings. We recommend using white lithium grease or similar.

•

Monthly

: Check the Power Unit’s Hydraulic Fluid levels. Refill if low.

⚠

WARNING:

Do not operate your Lift if you find issues; instead, take it out of service, then

contact your dealer, email

[email protected]

, visit

bendpak.com/support

, or call

(800) 253-2363

, extension 196.

Содержание MD-6XP












































Результаты поиска

Содержание MD-6XP

Отзывы:

BendPak MD-6XP, Инструкция по установке и эксплуатации, Страница: 33 / 44

Результаты поиска

Содержание MD-6XP

Отзывы: