BendPak MD-6XP Скачать руководство пользователя страница 11

Страница: 11 / 44

MD-6XP Mid-Rise Scissor Lift

P/N 5900108 — Rev. F — March 2020

Installation

This section describes how to install an MD-6XP. Perform the steps in the order listed.

⚠

WARNING

Use only the factory-supplied parts that came with your Lift

. If you use

parts from a different source, you void your warranty and compromise the safety of

everyone who installs or uses the Lift. If you are missing parts, visit

bendpak.com/support

or call

(800) 253-2363

, extension 191.

Safety Rules

When installing the Lift, your safety depends on proper training and thoughtful operation.

⚠

WARNING

Do not install this equipment unless you have automotive Lift installation training.

Always use proper tools, such as a Forklift or Shop Crane, to move heavy

components. Do not install this equipment without reading and understanding this
manual and the safety labels on the unit.

BendPak recommends referring to the ANSI/ALI ALIS Standard (R2015)

Safety Requirements for

Installation and Service

for more information about safely installing, using, and servicing your Lift.

Only fully trained personnel should be involved in installing this equipment.

Pay attention at all

times.

Use appropriate tools and equipment. Stay clear of moving parts.

⚠

WARNING

You

must

wear OSHA-approved (publication 3151) personal protective equipment

at all times when installing, using, maintaining, or repairing the Lift: leather gloves,

steel-toed work boots, eye protection, back belts, and hearing protection are

mandatory

Tools

You may need some or all of the following tools:
•

Hammer, mallet, crowbar, or pry bar

•

Open-end wrench set

•

Socket and ratchet set

•

Medium crescent wrench

•

Medium flat screwdriver

•

Tape measure

•

Fork Lift or Shop Crane

Содержание MD-6XP












































Результаты поиска

Содержание MD-6XP

Отзывы:

Похожие инструкции для MD-6XP

Бренды по названию

Популярные бренды

BendPak MD-6XP, Инструкция по установке и эксплуатации

Результаты поиска

Содержание MD-6XP

Отзывы:

Похожие инструкции для MD-6XP

Бренды по названию

Популярные бренды